Product Description:
Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.
| Size | DN50mm-DN600mm |
| Design standard | API609/EN593 |
| End flange | DINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150# |
| Face to face | API609/EN558-1 |
| Top flange | ISO5211 |
| Body | Ductile iron/Cast iron |
| Disc | Ductile iron/CF8/CF8M/C95400/C95500 |
| Stem | SS420 |
| Seat | EPDM/NBR/Viton/PTFE |
| Actuator | Bare shaft/Lever/Gearbox and handwheel |
| Coating | Epoxy/Nylon/PTFE |
| Pin | With out pin |
| Suitable medium | Water/Seawater/Sewage/Air/Foodstuff/Oil |
- Q:What do you mean by "2" and "200 CF8M"?
- CF8M is 316,2 "is 50200 caliber stainless steel pressure (American Standard, LB)
- Q:Why does the centrifugal pump start and stop in the case of closing the gate valve?
- After the valve is closed to stop the cause of centrifugal pump outlet valve is closed to stop the pump to prevent the flow back into the pump, impeller, impeller in reverse, part of the mechanical seal in the pump pump impeller reversal will have adverse consequences, serious damage to the centrifugal pump, to close the valve after the shutdown.
- Q:Valve flange drawing n- up to what
- A bolt hole used to indicate a flangeThe value of N indicates the number of bolt holesUp to the numerical representation of bolt hole size
- Q:Z41T one 10 gate valve and Z44T one, 10 gate valve difference
- Z41T one, 10 is single gate, Z44T one, 10 is double gateAccording to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== connection: flange type1== structure: Rigid single gate4== structure: Rigid double gateT== sealing surface material: copper alloy10== pressure rating: 1.0MPa
- Q:What type of flange does it fit with the gate valve?
- According to the welding plate flange, flange material selection of piping material.
- Q:Internal screw current limiting gate valve (Tan Gang) PN5.0 DN15/ Phi 1 Rc1/2 what does that mean?
- We did thatInternal thread current limiting gate valve (Tan Gang)Body material: carbon steelPressure rating: PN5.0 = 300LB American StandardNominal = DN15 = 1/2"Phi 1 = in the middle of the gate drilling a Phi 1 hole, so that in closing there will be a certain flow, that is, the minimum flow, that is, the current limit.Rc1/2 is thread, which is the connection
- Q:What is the soft seal gate valve?
- Cautions for installation and maintenance of soft sealing gate valve:For double gate valves, the direction of installation shall be in the vertical position of the valve stem, and the handwheel at the top.The installation of the soft gate valve shall be carried out in strict accordance with the installation environment, installation conditions and installation procedures on the factory manual.After installation, the soft seal gate shall be periodically checked for performance and killed in the cradle before any undesirable conditions occur.
- Q:What does gate valve DN80-PN16-QT450 mean?
- DN80 means: liquid, internal thread connection, the valve sealing surface material for rubber, seat sealing surface material for lining adhesive, nominal pressure of 10 kg / cm2, nominal diameter of 80mm Iron Butterfly valve.
- Q:Is the gate valve flanged?
- The most commonly used gate valves are threaded connections, flanged connections, and welded connections.Like the outer thread connection, the clamp connection, the card sleeve is seldom used.
- Q:TitleThe difference between gate valve, butterfly valve and stop valve
- The gate (gate valve) is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle gate valve. The direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle.Gate valve advantages: 1, fluid resistance is small,.2, opening and closing more labor-saving,.3, medium flow unrestricted, not disturbed flow, do not reduce pressure,.4, simple shape, structural length is short, manufacturing process is good, a wide range of applicationsValve shortcomings: 1, between the sealing surface is easy to cause erosion and abrasions, maintenance is more difficult,.2, big size, open need some space, opening and closing time is long,.3, the structure is more complex
1. Manufacturer Overview |
| Location |
|
| Year Established |
|
| Annual Output Value |
|
| Main Markets |
|
| Company Certifications |
|
2. Manufacturer Certificates |
| a) Certification Name |
|
| Range |
|
| Reference |
|
| Validity Period |
|
3. Manufacturer Capability |
| a)Trade Capacity |
|
| Nearest Port |
|
| Export Percentage |
|
| No.of Employees in Trade Department |
|
| Language Spoken: |
|
| b)Factory Information |
|
| Factory Size: |
|
| No. of Production Lines |
|
| Contract Manufacturing |
|
| Product Price Range |
|
