Lucky Aluminum Bars - AA1050 D.C Mill Finished Aluminum Circles for Cookware
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3 m.t.
- Supply Capability:
- 10000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
1.Structure of AA1050 D.C Mill Finished Aluminum Circles used for Cookware Description
AA1050 D.C Mill Finished Aluminum Circles used for Cookware is widly used in building, industry ect. Its weight is much lower than steel. So many customers choosed aluminium material instead of steel.
AA1050 D.C Mill Finished Aluminum Circles used for Cookware is one semi-finished aluminium material. This strip can be rolled down to aluminium foil.The final thickess can be 5-20 microns. Aluminium foil is soft, ductile and with a silver-white luster which can be widely used in a large scare of fields.
2.Main Features of AA1050 D.C Mill Finished Aluminum Circles used for Cookware
1）Surface Quality : be free from Oil Stain, Dent, Inclusion, Scratches, Stain, Oxide Dicoloration, Breaks,
2）Corrosion, Roll Marks, Dirt Streaks and other defect which will interfere with use
3）Fine craftsmanship
4）Durable
5）Easy processing
3.AA1050 D.C Mill Finished Aluminum Circles used for Cookware Images
4.AA1050 D.C Mill Finished Aluminum Circles used for Cookware Specification
Alloy | AA1050 |
Temper | H14, H16, H18,O/F |
Thickness | 0.5mm -- 4mm |
Diameter | 200mm -- 1200mm |
Standard | GB/T 3880-2006 |
5. FAQ of AA1050 D.C Mill Finished Aluminum Circles used for Cookware
What is the quality standard?
---Usually our standard is GB3880-2006
What is the largest width?
---It is 2300mm
- Q: What does aluminium bar 5052 mean?
- Seven, 5052-, H34 aluminum plate series and 1060 Aluminum plate series differenceHardness: 1060, the tensile strength of aluminum plate is between 110-130, while the tensile strength of the 5052 series is 210-230, that is to say, 5052 of the hardness must be 1060 of the response, 100% higher.Elongation: 1060 series of elongation rate of 5%, while the 5052 series of elongation reached 12-16% between, can also think so, in the 5052 series than 1060 hard 100% cases, the elongation rate has increased by about 200%.Chemical property: 1060 is pure aluminium plate, 5052 is alloy aluminium plate, 5052 corrosion resistance is better in special environment.Eight, relevant product standardsNational standard for aluminum strip (GB/T 3880-2006), applicable to the uniform standards of aluminum alloy sheet and strip materials. StopDu know who cited "Hondar Sheng 252" was released on 2017-01-08 16:43 | wonderful answer comment 0
- Q: What is the difference between the price of aluminum ingot and the price of aluminum bar?
- GB aluminum rod, generally in the aluminum ingot spot price based on a few hundred dollars, plus energy costs, losses, silicon, magnesium and other accessories fees, labor and so on. Non standard aluminum rod production scrap, the price is cheaper, but it is also the main reference aluminum spot price pricing.
- Q: Which of the 6061 aluminum bars, heat treated and 7075 aluminum rods, has been treated with heat?
- Secondly, the different states also have great influence. From the highest hardness, 7 lines, 2 lines, 4 lines, 6 lines, 5 lines, 3 lines, 1 lines are reduced in turn. The range of 6061 is much larger than that of 7075.
- Q: Use of 6063 Aluminium bars
- Building materials, irrigation pipe, extrusion materials for vehicles, bench, furniture, lifts, fences for decoration, aircraft, ships, components and light industrial departments and buildings in different colors.
- Q: What causes liquid leakage in casting aluminum bars?
- The plate is late because of the drive, the aluminum temperature is low, or it is slow, or cooling too strong.Aluminum leakage is the reverse, while the mold water shortage, and so on.It is possible to leak the aluminum when the plate is placed, but the position of the leakage aluminum is below the first cooling position.Moreover, if the aluminum liquid fills the plate, if the mold is full of time, if it is a lot worse, it may also be partly cooled enough and partly cooled enough.The height of the disc is not appropriate also affected. If too high, leakage of aluminum and plate will occur simultaneously.When the aluminum is low, the waiting time is short and can be a bit of a difference.
- Q: Why should two two iron bars and two aluminum rods be used in a water heater?
- The purpose of these techniques are to deceive others that water quality is bad, in fact, can only show that water conductivity is large, and the quality of water is not necessarily associated.
- Q: Introduction of aluminium bar
- Six, 6000, 6063 representatives of the 6061 series aluminum rod mainly contains two elements of magnesium and silicon, so the advantages of 4000 series and 5000 Series 6061 is a cold forging processing of aluminum products, suitable for applications in corrosion resistance, oxidation resistance of high requirements. The utility model has the advantages of good usability, easy coating and good processability.The seven and 7000 series of aluminum bars represent 7075, mainly containing zinc. Also belong to Aviation series, is aluminum, magnesium, zinc, copper alloy, is a heat treatable alloy, belongs to ultra hard aluminum alloy, has good wear resistance. Basically rely on imports, China's production process has yet to be improved.The eight and 8000 Series aluminum bars are 8011 commonly used. They belong to other series, and most of them are aluminum foil, which is not very common in the production of aluminum rods.
- Q: Why would the stick saw be cut in the aluminum bar?
- In the cutting process of aluminum bar or aluminum plate, the phenomenon of sticking aluminum on the saw plate is often occurred, which is why?In the cutting process of aluminum and aluminum rod, aluminum and aluminum rod because its weight is relatively large, in the cutting process in the open section will return to the middle of contraction, this will produce a large amount of heat and friction plate sawing aluminum rod and aluminum, high temperature melting aluminum will stick in the saw plate, such as cutting fruit the lubricating oil is not well, often saw card, machine equipment will be suspended.
- Q: I have an aluminum bar with a diameter of 14MM and a dent at the end of the bar, 4 wide and X10.5 deep,
- Is it efficient to use saw cutters? We use the vibrating plate to cut the material on an automatic machine. How many can we do in a minute?Chasing the answerThe efficiency is quite high. By the way, do you want the bottom of the groove flat or recessed? If you want to go in, you must use R2's convex semicircle cutter.
- Q: Excuse me, what's the temperature and speed of the 6063 aluminum bar casting?
- Now die-casting aluminum process according to material size, with electric furnace heating to 600-700 degrees. Small material high temperature heating, aniseed low, or too soft, not easy to move.It doesn't make sense to ask such questionsOr find their own information it!
Send your message to us
Lucky Aluminum Bars - AA1050 D.C Mill Finished Aluminum Circles for Cookware
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3 m.t.
- Supply Capability:
- 10000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
