750V Rubber Flexible Welding Cable 2014

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Packaging Detail:	in coils or standard export wooden drums
Delivery Detail:	25-30 days

Welding Cable
1.450/750V single rubber cable
2.flexible copper core
3.Used for industrial

Q: I have dell optiplex 755 @ Q6600I bought a new graphic card, HD4850it requires 2 IDE power connections,but my computer has just SATA connections.I saw sata-to-ide converter in the internet,but in my country there isn't any store that sells it.What should I do ?: are okorder /.... Look at the second to last picture, the small black 6pin connector next to the copper heatsink is what you need to use. I'm guessing that in thebox you got a 4pin molex y splitter to use in case you don't have a 6pin connector from your power supply. Put the 4 pin y splitter back in the box and look for a lead coming from the power supply that has the matching 6pin. Dell's have used the 6pin connector for a while.

Q: Cannot find a path to send the power cable for the amplifier through: The firewall is the bulkhead between the Passenger compartment and the engine bay. Look for a rubber grommet in the firewall/bulkhead that has existing wires going through it and use this. Some firewalls have grommets that you can use to pass your power cable through from the battery. Remember to put an in line fuse on th live cable of the correct rating.

Q: Hey.I just took out the power cable on my ps3, but then my light was gone in the same moment?How could that be :-D?: Bad wiring in the house? Sounds at least like a situation like that. Not uncommon in buildings of certain times.. older types of wiring used. And worse not ready for todays amount of electronics. So yeah check the wiring. In between time buy a few extension boxes, you know the type with more then 1 electronic socket. But most important a switch. That way you can switch it off and that way such discharges won't happen any more.

Q: I want to install a Bazooka Powered Sub (EL84-HP) to my car. I currently have a Pioneer 4-channel 600-watt amp that has a direct power line from the battery. However, I do not want to run another power line from my battery to my Bazooka sub, which has it's own built-in 100-watt sub. Would it be OK to connect the power cable only from my Pioneer amp to my Bazooka sub?: Only if you dont value either of them.

Q: I just got a cheap intel i3 custom pc build on OKorder. But, i have no idea on how to set up all those PSU cables and the fans and everything else (seller thought it was a great idea to unplug every cable inside, which led to me turning on the pc assuming everything was good to go which led to the cpu overheating after turning it on) But anyway, i need to know how to setup the psu cables. My PC looks like a mess with all those cables jumbled up together. There are 4 distinct think cables sticking out from the PSU and all the other cables come from the case or the fans. Some of the cables come with numbers (1, 2, 3) and some are already plugged into the mobo, so i don't want to touch those. How to do this?: CD/DVD drives and hard drive all use the same power connectors (multicolored), so plug them in whichever way you want. There is no specific order. Don't remove any ribbon cables, and if you wish to have a floppy drive, the power cable is slightly smaller than normal ones. Commonly, fans can be plugged in to any port on the motherboard as long as they reach without straining the cable. They can only be inserted one way and are likely three-prong so it should be easy. The numbers on your cords don't matter.

Q: ok, i want to install and upgrade the sound system in my car, volkswagen 2006, but i dont know where to run the power cable from the battery in engine compartment to the trunk where i place the amplifiers, anyone who knows, please help me out. thanks: from the trunk down the side of the car (pop open the panels that sit on the bottom where the door closes. run the wire thru the firewall grommet where the ignition and internal power wires run thru. Use a coat hanger duct taped to the power wire to get it thru. should go thru with some pressure. just finished dropping in an amp in my accord.

Q: a. the potential difference between the forward and rear feet when the bear crawlsb. the potential difference between the bear and the cablec. the coulomb force between the bear who obtains charges when passing by the cable and the cabled. none of them: a. when the wire touches the ground, it sets up an electric field that gets smaller as it gets further away from the wire. If the voltage is high enough, then the difference between the bear's front and hind legs might be enough to shock the bear. If you are ever in a situation where you are near a downed power line and you MUST get away, you should try hopping away on one foot, or at least keep both feet as close together as you can.

Q: What are the advantages and disadvantages of separating 28Vdc, 200A positive power cables and returns into two different harnesses?: WHAT ARE YOU TALKING ABOUT ? ALL DC POWER SOURCE REQUIRES TWO SEPARATED CABLES .

Q: Hi. I have an iBook power cable and I was wondering if there was a way to adapt it so I can use it for my new MacBook Pro that uses a magnetic cable? Thanks!: you could try but you could blow your the new computer so I wouldn't try

Q: I have 8x220ah deep cycle car battery's at 12v and i wanted to run an 5kw 12v power inverter but i would need cable which is 400amp 12x4004800 so could i use two cable connected to the battery's and split the power into 2 cable or would this not work if so whythe inverter would be using 400amps from the battery and it would be supplying 20amps at 240voltsis my working out correct: In this case, you should have put the batteries in series to get 48 or 96 volts, that makes the cabling easier. Too late now. Yes, at 5kW, that is 5000/12 420 amps I don't know what size wire you are using, and what the distance is, so I can't help further without that information. For example, if you are running 10 feet of cable (20 total) and you want to lose only 5% of the voltage, which is 0.6 volts, then the resistance of the wire needs to be less than 0.6/420 1.4 mΩ. That is, over 20 feet, 71 mΩ per 1000 feet, which is 000 AWG wire. Mush more than 10 feet, and you need to use MCM wire. .

Send your message to us

*Email

*TEL

*Quantity

*Unit