Aluminum Foil 18 X 500

Hot Products

Double Side Aluminium foil laminated to fiberglass cloth

aluminum foil with LDPE film heat sealing for bubble foil facing production

aluminum foil with LDPE for bubble foil insulation production

aluminum foil with LDPE for bubble foil facing production

aluminum foil with LDPE heat seal for bubble foil facing production

Double side Aluminium foil laminated to fiberglass cloth

heat insulation material for building

Aluminum Foil Coated Bubble Insulation FBF101

Double Side Aluminium foil laminated to PE woven fabric

FSK Heat Insulation materials

FAQ

I added a screened room to my mobile home. I also have vinyl windows. in the summer the sun beats down on the home almost all day Someone told me I could have insulation installed in the roof panels, and that i may even be able to do it myself. Right now it's impossible to enjoy my patio between 1-5pm because it so hot you can't breath. I'm in the Pasco, FL area - 34667Appreciate any help you can give

I agree with RustyNail that the panels are thin and not meant to support that kind of weight. But, I think a wall anchor that spreads the weight inside the foam would work if that's the only place to attach. I'm imagining that there's no wall available since these usually are just supported at the ends. If so, then my first suggestion would be no curtains at all. My second would be to find a long wall anchor. With 6" of foam, I would think you could do a 4" long anchor and get pretty good support. Rusty may disagree.

we want to put a model railway up in the loft,and i like the idea of having white plastic cladding throughout up there,my hubby is insulating the roof tomorrow,but he prefers plasterboard,at least the cladding will be maintenance free,

i think it might be able to pass code if you ever sell the house.i myself would use sheets of white wainscoting.also make sure the insulation if it has a paper backing ,paper faces the room.

I gutted the room and now would like to rebuild. One side of the room slants (it's the roof) and the other side of the room is a dormer (all low ceilings).I want to insulate the ceiling but have no ridge vents so no moving air as someone mentioned I should have. I want to install foam channels to keep the insulation away from the roof but not sure if this is a good idea without the ridge vents. I will have a vent to the outside installed on the very top of the roof however and the small attic space is open all the way through the other two upstairs rooms and I will add another roof vent on that end of the house. I will only be able to install 3 inch insulation but that's better than none at all. I live in the northeast and was told if the job isn't done right I can get ice jams in winter. Also I don't see any way to drill ridge vents. would it be ok to just install the styrofoam channels and insulate then sheet rock or am I asking for trouble? Thanks in advance for any help.

Suggestion: install the insulation with the foam channels but leave the center section (roof ridge area) open from end to end. At each end you can install a static vent or an active one. Depending on the amount of space you have you may be able to install a power vent.If you can send me a diagram with measurements I can give you a more definitive answer.

I know you're not supposed to directly insulate the roof due to the roof getting super heated in the summer, but my walk-in (actually, more like "crawl in") attic is very hot in the summer and very cold in the winter. Is there anything I can do to improve efficiency? I can't help but think I'm wasting a lot of energy just to keep my roof lasting a little longer.

You can avoid the condensation problem by simply leaving a minimum 2'' gap between the roof and the insulation. You need to fix battens on to the rafters ( at least 2'' from the tiles ) and then fix blanket or rigid insulation tight between them. The battens will maintain the air space. You then need to fix a vapour barrier over the whole thing and finish with plasterboard. No small job to do it properly ! ps you need to check the condition of the roof before you start and fix any loose tiles etc Alternatively, turn the heating up and wear a thicker sweater.

hi me and my friends made a lounge out of my old tin roof shed we have a tv speakers and a few other electrical goods... since winters on its way we were wondering whats the best and cheapest way to insulate the place note that its a tin rof but has wood under it where the old indulation used to be the place is pretty chilly and sometime damp plz help we dont wanna be freezing our asses off in there thanks :)

I would look at using the pink insulation if it will fit between the tin roof and the under it, If not, you may have to remove the wood to install the insulation.

a roof that is built with the insulation covering the waterproof membrain is ?

Not done properly.

I'm thinking of converting my brick walled corrugated iron shed into a changing room for winter hot tub use. I was advised by a friend that the first thing i should do is insulate the roof using glass fibre insulation (the yellow fluffy stuff in the loft) and a simple Plywood ceiling but im not sure how i would stick it to the existing roof (dimensions 170cm x 147cm). So..... how should i insulate the roof of my future changing room????

What is he using glue on? Buy rolled fiberglass insulation, install it between the rafters and wall studs...paper side in. You can cover the walls and ceiling with drywall, OSB, plywood if you wish. You do realize that insulating your shed isn't going to make it much/any cooler don't you? You will need an air conditioner for that, but the insulation will help keep the AC in.

House is a bi-level. Recently added storm windows to deck off dining room. Having a new rubber roof installed would like to know if we can insulate ceiling to make the room warmer. What product do you suggest we use. we are getting conflicting answers, some say you can insulate others say the ceiling needs to breath having a rubber roof install. Please advise.

If you have vaulted ceilings you need to get the right insulation. Basically it wont be as thick and still leave some room between the insulation and the roof for it to breathe. You should be able to get it at any home improvement place.