Saddle

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
10 Pieces pc
Supply Capability:
1000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

  

Saddle

 

1), Product Information 

We supply coupling  for all over the world and product surface shall be smooth and free from sand holes, blow holes, distortion or any other defects.

 

2), Material

Body:

Ductile iron grade 500-7/ 450-10 in accordance with ISO 1083 or 70-50-05/65-45-12 with ASTM A536

 

Gland:

Ductile iron grade 500-7/ 450-10 in accordance with ISO 1083 or 70-50-05/65-45-12 with ASTM A536

 

Gasket:

Rubber E. P. D. M. /SBR/NR in accordance with EN 681.1

 

T-BOLTS AND NUTS:

Carbon steel grade 8.8/6.8/4.8 with dacromet coating/galvanization

 

3), Process

* Resin Sand

* Molding Boards

* Green Sand with hand molding

 

4), Inscription Style

* As per customers' requests

* Standard Inscription(EN545;PN--;DN—OD--)

 

5), Packing

* Wood box

* As per customers' requirements

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the installation requirements of the card sleeve joint?
The ends of the pipe shall be flush. The pipe should be flush in sawing grinding wheel and other tools, and burr cleaning and high pressure air blowing after use.When installing, the coaxiality of pipe and joint body should be kept as far as possible. If the pipe deflection is too large, it will cause sealing failure.The pre assembly force should not be too large. The inner blade of the clamping sleeve is just inserted into the outer wall of the pipe, and the clamping sleeve should not be deformed obviously. When the pipeline connection, and then according to the specified tightening force assembly. The tightening force of the phi 6-10mm card sleeve is 64-115N, Phi 16mmr 259N, Phi 18mm is 450N. If the sleeve is badly deformed at pre assembly, it will lose its sealing effect.(2) prohibit adding sealant and other fillers. In order to obtain better sealing effect, the sealant is coated with sealant, and the sealant is poured into the hydraulic system, causing the hydraulic components, such as damping holes, blocked and so on.(3) when connecting the pipe, the pipe should have enough deformation allowance to avoid the tensile stress of the pipe.(4) when connecting the pipeline, it should be avoided to be subjected to lateral force; the lateral force will cause the seal to be too lax.
Q:What do you mean by the next connection in the pipe connection? How do you use it?
It is the through plate connection, when the joint goes through the iron plate and the like, use the next joint
Q:PE pipe joint and PPR joint can be with each other
I can'tPE is polyethylene, and PPR is random copolymerized polypropylene
Q:20ppr pipe joint is not what brand, 20ppr pipes can weld?
Pipe fittings and pipes produced by different manufacturers are not necessarily the same in proportion to raw materials
Q:G1/8 "pipe joint end special sealing WD-B02 is what mean
WD circle of different names is divided into: ED ring, ED ring, hydraulic pipe joints, pipe joint gasket seals and so on, the use of pressure: 5 (MPa), the use of temperature: 200 (c), properties: corrosion resistance, high temperature resistance, abrasion resistance, applicable scope: pump, cylinder, sealing, effect material: nitrile rubber (NBR) fluorine rubber (VITON).
Q:The pipe line of the hydraulic pressure pipe is formally installed
Hydraulic pipe fittings - thread standard twoClassification of threadsThe 1. threaded internal and external threads two;2. according to the shape of teeth can be divided into: 1) triangular thread 2) trapezoidal thread 3) rectangular thread 4) sawtooth thread;3. by line, single, head and multi thread;4., according to the direction of rotation, two kinds of left and right threads, the right is not marked, left plus LH, such as M24 * 1.5LH;5. according to different uses are: metric common thread, thread sealed pipe thread, non threaded sealing pipe thread, 60 degrees taper pipe thread, metric taper thread, etc.Two. Metric general threads1. metric screw thread with a capital M, tooth type angle 2 degrees =60 (alpha tooth type half angle);2. metric ordinary thread by pitch, coarse teeth, ordinary thread and fine teeth, two kinds of ordinary thread;2.1. coarse tooth ordinary thread mark generally does not indicate the pitch, such as M20 means coarse thread; fine tooth thread mark must indicate the pitch, such as M30 * 1.5 for fine tooth thread, in which pitch is 1.5.
Q:What's the meaning of the pipe joint 14-M18*1.5? What's the thickness of the wall?
(two) prohibit adding sealant and other fillers. Some people in order to obtain better sealing effect, in the card cover with sealant, the result of sealant is poured into the hydraulic system, causing hydraulic components, such as plugging holes. (three) when connecting the pipe, the pipe should have enough deformation allowance to avoid drawing the tube. (four) when connecting the pipeline, the lateral force should be avoided, and the lateral force will cause the seal to be too tight. (five) when connecting pipelines, should be a one-time good, avoid repeated disassembly, otherwise it will make poor sealing performance. Sleeve type pipe joint installation (1) of the pipe should need pickling pickling treatment according to the ninth chapter; (2) tube machine equipment cut tube with special cutting or sawing machine according to the required length, absolutely not allowed by fusing (such as flame cutting) or grinding wheel cutting; remove pipe end burr, metal cutting inside. Dust and dirt; remove the rust and dirt pipe joint; and also to ensure pipe roundness; (3) the sleeve nut, successively sheathed in the pipe sleeve front edge (small end) from the pipe mouth at least 3mm, then the pipe is inserted into the connector body bore, top to check; (4) slowly tighten the nut, while rotating the pipe until does not move, then tighten the nut 2/3 ~ 4/3 circle; (5) open the check card sets whether has cut the pipe correctly. The clamping sleeve does not allow axial movement, but slightly rotates; (6) after checking, tighten the nut again.
Q:What does national standard joint jb/t6381.2-92 mean?
The current version is: JB/T, 6381.2-2007, cone welded, straight through, 55 degrees, non hermetic, pipe, threaded, pipe joint. The type, size and technical specifications of the taper sealing welded straight through 55 degree non sealing pipe thread pipe joint are specified.
Q:Standard for fabrication of jacket type pipe couplings for card sleeve couplings
6 flared flared joint (GB/T 5630-2008)7 、 flared type adjustable end bend pipe joint (GB/T 5631-2008)8 、 flared type combined bend pipe joint (GB/T 5632-2008)9 、 flaring type adjustable end to end three way pipe joint (GB/T 5633-2008)10 、 flared type combined bend three way pipe joint (GB/T 5634-2008)
Q:PPR pipe joint leakage, do not want to change pipes, what is the good way?
Can change the best, or else with strong glue, there is a special plug on the water pipe glue, you should first put the pipe water, and in the case of clean surface to glue
We have three foundries, and our main products are casting iron products for construction and water treatment field. We are willing to join in hands with both new and old clients to make the most sincere communication.Please contact us.

1. Manufacturer Overview

Location Shandong, China (Mainland)
Year Established 2006
Annual Output Value US$10 Million - US$50 Million
Main Markets North America
South America
Eastern Europe
Africa
Mid East
Western Europe
Company Certifications ISO9001

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Qingdao
Export Percentage English, French
No.of Employees in Trade Department
Language Spoken: 11-20 People
b)Factory Information  
Factory Size: 5,000-10,000 square meters
No. of Production Lines 3
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average