Insulator Pin

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
2000 Pieces pc
Supply Capability:
200000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

insulator end fitting  

Strength grade:40KN----550KN

Material:C45,35Mn2,40Mn2, 45Mn2

Standard:IEC,ANSI

Hot dip galvanization 

 

Brief

Ball type pin for suspension Insulators application

Materials in C45, 35Mn2, 40Mn2, 45Mn2

Zinc sleeve optional

Mechanical class 40kN - 550kN

Hot galvanized coating protection against corrosion

Magnetic article test on100% of components

 

Standards

Materials testing acc.to EN10083-1,-2, AISI-SAE J403

Dimension testing acc.to IEC 60120, ANSI C29.2

Galvanization testing acc.to IEC 60383, ISO 14713, 1461, ASTM A123, A153

Galvanization thickness level test as below table

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The name of the card sleeve joint
Or 1 inch single (head) card sleeve and 1 inch double (head) card sleeve
Q:How are the sleeve couplings joined?
Generally used in high-pressure pipe, steel pipe, copper pipe, iron pipe are used
Q:What's the meaning of the pipe joint 14-M18*1.5? What's the thickness of the wall?
(two) prohibit adding sealant and other fillers. Some people in order to obtain better sealing effect, in the card cover with sealant, the result of sealant is poured into the hydraulic system, causing hydraulic components, such as plugging holes. (three) when connecting the pipe, the pipe should have enough deformation allowance to avoid drawing the tube. (four) when connecting the pipeline, the lateral force should be avoided, and the lateral force will cause the seal to be too tight. (five) when connecting pipelines, should be a one-time good, avoid repeated disassembly, otherwise it will make poor sealing performance. Sleeve type pipe joint installation (1) of the pipe should need pickling pickling treatment according to the ninth chapter; (2) tube machine equipment cut tube with special cutting or sawing machine according to the required length, absolutely not allowed by fusing (such as flame cutting) or grinding wheel cutting; remove pipe end burr, metal cutting inside. Dust and dirt; remove the rust and dirt pipe joint; and also to ensure pipe roundness; (3) the sleeve nut, successively sheathed in the pipe sleeve front edge (small end) from the pipe mouth at least 3mm, then the pipe is inserted into the connector body bore, top to check; (4) slowly tighten the nut, while rotating the pipe until does not move, then tighten the nut 2/3 ~ 4/3 circle; (5) open the check card sets whether has cut the pipe correctly. The clamping sleeve does not allow axial movement, but slightly rotates; (6) after checking, tighten the nut again.
Q:About thread, pipe joint standard question
For thread purposes, you are recommended to study the metric, American and American thread standards manual
Q:Maintenance skills of fire hose clamp joint leakage
A fuse is generally used when Water Leakage threaded connection, trench connection pipe to check whether the sealing surface is flat and smooth, without burr. Whether the sealing surface of the sealing ring is scratched and whether the length of the sealing section meets the requirement. These are three guarantees. They won't leak.
Q:Can the pressure vessel pipe joint adopt G thread? Why?
Can not. G threads are not sealed enough.The following three threads can be used.1.55 degrees taper external thread R and cylindrical external thread Rp matching2.55 degrees taper external thread R and taper external thread Rc fit3.60 degrees taper internal and external thread fit PT.Glass can not be sealed only by thread.
Q:Consult the problem of the pressure at the entrance and exit of the pipe joint
Assuming that your 3 oil outlet, load is infinite, as follows, three load (cylinder or motor) are not action, three outlet pressure is 2MPa, three outlet pressure gauge pressure is 2MPa
Q:What is the manual pre assembly procedure for the EO-2 joint?
4, the pre assembly force should not be too ambassador, the inner edge of the card sleeve is just inserted into the outer wall of the pipe, and the clamping sleeve should not have obvious deformation. When the pipeline connection, and then according to the specified tightening force assembly. Phi 6-1 card sleeve tightening force is 64-1 15N, 16 MMR 259n, Phi Phi 18mm for 450n. If the sleeve is badly deformed at pre assembly, it will lose its sealing effect.Matters needing attention:1, prohibit adding sealant and other fillers. Some people in order to obtain better sealing effect, in the card cover with sealant, the result of sealant is poured into the hydraulic system, causing hydraulic components, such as plugging holes.2. When connecting the pipe, should make the pipe has enough deformation allowance, avoid the pipe by tensile force.3. When connecting the pipeline, it should be avoided to be subjected to lateral force, lateral force caused by the assembly seal is not strict.4, when connecting the pipeline, should be a one-time good, avoid repeated disassembly, otherwise it will make poor sealing performance.
Q:Who knows what the clamp joint standard is?
There are a lot of standard for fast mounting clamps.The actual production of the ISO clamp joints seems somewhat different from the standard,
Q:PEX floor heating pipe fittings and fittings are aluminium plastic pipes?
Its advantages and disadvantages:(1) good mechanical performance;1., good pressure resistance, shock resistance, rupture resistance2., with a strong plastic deformation ability, can be greater than 5D radius within the arbitrary bending, without heating, not rebound; (D for pipe diameter)3. light weight, same flow diameter composite pipe weight is 1/3 of steel pipe, 1/12 of galvanized pipe;
We are a manufacturer and trading group specializes in the export of metal products. It mainly deals with various of ferrous metal & nonferrous metal castings and forgings, our main products covering water valves and fittings, power line fittings,fire-fighting equipments, motor & pump part, automotive & machine parts,.etc.

1. Manufacturer Overview

Location Dalian,China
Year Established 1994
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port dalian
Export Percentage
No.of Employees in Trade Department
Language Spoken: English,Chinese
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range