Q:What crusher is used for raw material of broken refractory material? What is the rough crushing process? What are the materials? Thank you!

Common faults and causes of magnetic?separator. 1. Motor of magnetic?separator is overheated and its sound is not normal. Reasons for this failure are: 1) lubrication of bearing is bad or badly worn; 2)fan blade falls off or wears; 3)bad contact of switching circuit or disconnected to run a single phase; 4) voltage is too low. 2. Reasons for this failure due to overheated speed reducer are: 1) lack of oil or poor kerogen; 2) wear between gear and worm, or poor mesh; 3)poor lubrication of bearing or serious wear. 3. The sound of magnetic?separator during operation is abnormal, lattice ball mill. Cylinder is stuck by obstacle, and even the cylinder can not rotate. The bottom box vibrates. Reason for this failure is often that it is stuck by objects in drag flask, otherwise magnetic?patch falls off so that the cylinder screaks and pierce tube when it is serious. At this time, car should be stopped for maintenance and troubleshooting. Only when we master common faults and reasons of magnetic separator can we timely identify problems and solve problems. Better maintenance and repair of magnetic?separator equipment are an important prerequisite to properly use equipment and ensure the construction.

Q:How to choose construction external wall thermal insulation and fireproofing materials?

The width of fireproof partition shuld be greater than 30CM, and the thickness should be the same as total thickness of thermal insulation materials. Fire barrier zone thermal insulation board and base wall should be stuck in whole area. Fire Barrier zone thermal insulation board should be stuck with the assistance of anchor bolt which must press the mesh of the bottom layer. Fire Barrier zone should be set above the door and window, with a distance of less than 50cm between the lower edge of fire barrier zone and the upper edge of window.

Q:Does the aluminum silicate thermal insulation material fireproof?

How does its fireproof?performance? this is the material that the decoration master worker recommands to me, how do you think of it?

Q:Does anyone know the difference between refractory and thermal insulation material?

The main difference between insulation bricks and refractory bricks are as follows: 1. Insulation effect The heat conductivity cofficient of insulation bricks is usually 0.2-0.4 (average temperature of 350 ± 25 ℃) w / mk while the heat conductivity coefficient of refractory bricks is 1.0 (average temperature of 350 ± 25 ℃) w / mk or more. Thus it can be seen that the insulation effect of insulation bricks is much better than that of refractory bricks. 2. Refractoriness The refractoriness of insulation bricks is generally below 1,400 degrees centigrade while the refractoriness of refractory bricks is above 1,400 degrees centigrade. 3. Density Insulation bricks are generally light-weight insulation material, and the density is generally 0.8-1.0g / cm3. But the density of refractory bricks is above 2.0g / cm3.

Q:How to divide fire resistant level of fire door?

Fire resistant level of fire door【Class A fire door】. Class A fire door is also called complete fire door. It can meet the requirement of fireproof thermal insulation and refractory integrity at the same time in specified time. Fire resistant levels are 0.5h(Grade C), 1.0h(Grade B), 1.5h(Grade A) and 2.0h, 3.0h. 【Class B fire door】Class B fire door is also called part heat insulation fireproof door. Its requirement of fireproof and thermal insulation performance is 0.5h. Refractory integrity levels are 1.0h, 1.5h, 2.0h and 3.0h respectively. 【Class C fire door】Class C fire door is also called not thermal insulation fireproof door. Ther is no requirement of its fire resistance and thermal insulation. It only meets the requirement of refractory integrity in specified refractory time. The grading of refractory integrity is 1.0h, 1.5h, 2.0h and 3.0h respectively. There is the content of not thermal insulation fire door in British BS standard.

Q:Who knows what fire heat preservation material are there?

It can be realized through inorganic insulation materials, such as glass wool, rock wool, foam glass etc.. The phenolic foam materials inside organic foam material is more special. Phenolic foam does not only have a good thermal insulation performance, but also can be combined with steel and other materials, to achieve a class A fire retardant level. Class A thermal insulation include: Rock (ore) cotton, foam glass, inorganic thermal insulation mortar, etc.. 1 thermal insulation materials with class A combustion performance Phenol, powder polystyrene particles etc.. Fire insulation materials of fire barrier zone can use class A material with class A combustion performance in rock (ore) cotton, foam glass, inorganic thermal insulation mortar. Hope my answer will help you.

Q:What level is the rock wool board fireproofing material ?

The fire rating classification is a provision for all insulation materials, rather than to separately divide rock wool. Determine the value of the material fire rating according to the relevant test items of 8624. As the rock wool is made from basalt fusion, so it is the level A non-combustible material.

Q:what's the classification of fireproof and thermal inuslation matertial?

1. thermal insulation material with A class combustion performance. Rock wool, glass wool, foam glass, foamed ceramics, foam cement, hole-closed perlite (2) thermal insulation material with B class combustion performance: extruded polystyrene board after special processing (XPS)/ polyurethane after special processing (PU) , phenolic aldehyde, gelatine powder polyphenyl granule. 3,thermal insulation material with B2 class combustion performance: molding polystyrene board(EPS), extruded polystyrene board(XPS), polyurethane (PU), polyethylene (PE),etc. sea capacity module and vitrified micro bead(cooperate with the innovator of vitrified micro bead, Liu Weihua) fireproofing issues have been completely solved.

Q:How long is the fire-fighting time of A class fire resisting window?

Duration of fire resistance of fire resisting window: A class window is not less than 1.2 hours; B class window is not less than 0.9 hours and C class window is not less than 0.6 hours. Technical Requirements: 1materials and accessories (1) window frame structure adopts stell framework and wooden framework that have a certain strength to ensure integrity and stability. (2) steel framework and batten can choose galvanized steel plate or stainless steel The selection criteria meet requirements of GB12955 steel fire door general technical conditions in the provisions of article 5.1. The selection criteria of wooden framework and batten meet requirements of GB14101 wooden fire door general technical conditions in the provisions of article 5.1.1. Filling material of steel and wooden framework shouldn't adopt non-combustibility material. (5) fire-fighting glass can adopt testing-qualified product that don't influence fire resistance performance of fire resisting window. Light transmittance of glass is not less than 75% of the same layer common plate glass. (6) Sealing material between framework and fire-fighting glass should adopt Flame retardant material which can serve as fire-fighting and smoke-resistant when encounter fire disaster. (7) hardware fitting should accessories product that is tested to be qualified. 二. installation requirement: 1. When Party A takes over goods, he should check numbers, specification, grades and whether Accessories are Conformed and complete according to contract.

Q:What is the the best ratio of mortar in refractory cement?

Specifical proportions are as following: 42.5R cement is 425 rapid hardening cement. Using the 425 cement to compound the mortar. The reducion of cement will naturally impact the workability of the mortar. The mix design standard of the mortar specifies the minimum amount of cement is not less than 200kg / m3. If it is composite mortar, and the strength and workability can be ensured, it is Ok to use 425 to compound. You can look for instructions of mixing proportion of mortar online as a reference.