Q:I have just learned how to make some pretty cool bracelets out of telephone wire and i would like to know where to find more telephone wire. Could someone tell me where i might be able to find some?

For the best answers, search on this site https://shorturl.im/awUe1 You can find these all over the internet, but you'd end up having to pay for them... You are looking for donations of end-of-life cables to make the baskets, I recommend trying some of the electronics recycling organizations that are becoming more and more prevelent. Electronics put tons of bad chemicals in our environment when they are thrown away, so more and more efforts are coming up to find ways to recycle them rather than throw them in a landfill. Look up End Of Life Electronics for some of the efforts out there.

Q:Hi i would like to ask what is the diference between the two versions of wiring the RJ 45 connector. when I was making my first networking cable, i used the wiring according to an image that only was using/connecting four wires into the connector. the cable works and works well. Now i found plenty of other images, all of them reccomending the full /eight wires/ connecting. Do I run my network on lower Mbits/sec? what are the other four wires used for? Thanks

In 10/100 Mbps wiring only 4 wires are used. 2 for sending data, 2 for receiving data. The other 4 are used for cancelling cross-talk and minimizing other problems associated with the physics of transmission. The wires are arranged in 4 pairs, with each pair twisted. It's the twisting that solves or reduces transmission problems. In Gigabit over copper (1000Mbps) all 8 wires are used, 4 for transmit and 4 for receive. The twisting of the wires is much tighter and the actual connectors on the ends have a smaller tolerance. You should also be aware that there are two major standards for wire arrangement in UTP data cabling - 568A and 568B. You will need to know what standard is used in your network for consistency's sake. Mixing 568A and 568B results in cross-over which may or may not be what you intended. Hope this helps.

Q:Two wires, 2.44 m apart, both carry current 2.2 A toward the bottom of the screen. The right wire is extremely long, and the left wire is 0.36 m long. What is the magnetic force on the left wire?

Magnetic force, F = BIL --------(1) where B is the magnetic flux density of the magnetic field caused by the right wire, acting perpendicularly to the left wire in Tesla I is the current in the left wire in Amperes L is the length of the left wire in metres To find B (due to the right wire), you have to use the formula B = (?0)(I)/(2πr) -----(2) where the I in this case is the current in the right wire, r is the distance between the two wires, and ?0 is the permeability of free space, numerically defined as ?0 = 4π×10?7 using eqn (2) so B (due to right wire) = (?0x2.2)/(2πx2.44) = 1.8x10^-7 T using eqn (1) and the value of B calculated above F = (1.8x10^-7 x 2.2 x 0.36) = 1.43x10-7 N

Q:In that chart it has 2 sections, one is maximum amps for chassis wiring and the other is maximum amps for power transmission. What is considered chassis wiring and what is considered power transmission?

Chassis wiring assumes each wire is routed separately, and power wiring assumes they are wired in a bundle. In chassis wiring the cooling of the conductors is better, because they are all exposed directly to air. In a bundle, some of the wires are not in direct contact withe the air.

Q:Im installing a motion sensor which comes with 3 wires,red black and white and want to connect it to a indoor light that only comes with 2 wires white and black.How do I go about installing them and powering them?

Hook the white wire to the white on the fixture and the white coming in. The black coming in gets wired to the black wire on the detector. The red gets hooked the the black in the fixture.

Q:The spark plug wire on my dirt bike needs to be replaced because it was touching the exhaust and it burned through.I was wondering if the ignition coil and spark plug wire are one piece and need to both be replaced or is there someway to disconnect spark plug wire? They spark plug wire doesn't seem to be pluged in, but it seems to be one piece. Does anyone know?

sophisticated situation. do a search from a search engine. that will could actually help!

Q:I've seen people use it as ...umm..energy generating...majiggy.. (but not alot of energy) including a magnet/something about a magnetic field or some sort?and instead of MAGNET WIRES can i use SPEAKER WIRES?(RADIO SHACK)

Magnet wire is just solid copper with a layer of varnish for insulation. Speaker wire would work, but you could not wind the wire as tightly due to the thicker insulation. also the wire is very flexible and will not stay in place very well. Also, if the coil gets hot, the insulation on the Speaker wire will start to burn or melt. .

Q:I'm trying to wire a Sony L410X stereo to my 2002 Chevy Silverado 1500. I don't want to use a wiring harness, so I'm trying to figure out how to splice the wires together. I don't know how to hook the power wires up correctly. Obviously hooking the speakers up will be easy. I've tried looking at the wiring diagram but it seems like on the stereo system diagram it's positive and negative whereas the truck wiring is not identifying the negative wiring, just 12v+ Constant and 12v+ Switching. Any guidance would be greatly appreciated!

get okorder /

Q:alright, 5 speakers with 4ohm svc, what would my wiring options be?

With 5 speakers there won't be a symmetral wiring pattern for even power distribution. With 4 it would be 2 pair in parallel with both sets in series for a 4 ohm final load or all 4 in parallel for a 1 ohm final load.

Q:i know nothing about wire. thanks. :|

Solder wire has a lower melting point, allowing you to melt it onto something else. In it's wire form, it will also snap very easily. (not good for fastening things together). Mechanical wire (I'm assuming electrical wire), is designed to withstand high temperatures (and hence, electrical currents), and are usually be bent much more. It's also usually sheilded in rubber (e.g. electrical cords, computer cables, coxial (tv) cable, etc).