Mini Valve, Mini Needle Valve
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 50 Pieces pc
- Supply Capability:
- 50000 Pieces Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Packaging & Delivery of Mini Valve, Mini Needle Valve
Packaging Details: ply wooden case
Delivery Detail: on your request
Specifications of Mini Valve, Mini Needle Valve
Mini Needle Valve, packing below stem threads; Standard Vee stem; pressures to 10000psi(689 bar);
Mini Needle valve ,instrument valve:
1.One piece bar stock construction with full material traceability.
2.Back seating of stems in a fully open position prevents stem b ackout.
3.Permanent locking of valve bonnet prevents accidental removal while operating valve.
4.Stem seal isolates the lubricated stem threads from the process.
5.Stainless steel models of needle, gauge and instrument manifold valves, equipped with needle stems, meet NACE MR-01-75.
- Q:Is the injection pressure tight after the valve pin closes?
- In the process of injection molding, solution and shrinkage because of cooling, but because the screw to move slowly forward, so that the material in the tube to melt into the cavity, to supplement the needs of shrinkage, called pressure. It means to prevent product shrinkage, with pressure if production is stable. The pressure can also adjust the product size, without weld line
- Q:Napping needle valve type hot runner gate part of what is the reason? Do you have any expert answers?
- Napping needle valve type hot runner hot runner valve gate part is the occasional problems encountered in the process of trial, when the production time will be such a problem.
- Q:Why hot runner valve needle Ti
- 1., small friction coefficient, smooth, small friction resistance, small wear, and prolong lifeBetween 2 and the metal is not easy to anti adhesion and anti affinity to improve product crumbs injury nap and then improving the machined surface quality of products
- Q:Why can hot runner needle valve be blocked?
- May be a small needle valve, or is not standard and not with the nozzle aperture valve needle understanding.
- Q:Hot runner valve needle broken inside how to do?
- Hello, you are pulling the valve needle, because the needle is too tight, the needle out of the head of the bar.
- Q:How to use the needle type oil cup
- Method of use: D needle type oil cup is a cup, the cup is a middle upper lid, from the top to the bottom through a needle valve, the cup cover is bending spring, pressure spring pressure to the middle of the adjusting nut adjusting nut to adjust the valve pin to the top of the lower end of the oil outlet open the upper part, and sideways to erect it can put the valve open to the maximum.
- Q:Needle valve hot runner outlet hole shrink what is the reason?
- The higher the temperature is, the greater the shrinkage, so when the product is cooled naturally, the needle valve has the largest shrinkage hole.
- Q:Mold glue is how the air valve needle
- The hot plate of the needle valve has operation instructions on it. If it is not clear for a long time, see if the hot runner leads out the interface. Is there any mark gas IN/OUT?If not, (usually two groups, only one group and one group)
- Q:Hot runner valve needle in the molding, why will retreat?
- The following reasons may cause the needle to recedeThe plastic pressure is greater than the cylinder pressure, causing the needle to recede
- Q:How many times can the hot runner valve needle be used?
- the international standard moldThe valve needle surface hardness of HRC60-62, titanium, with non stick material, high abrasion resistance, continuous use up to 1 million times,
1. Manufacturer Overview |
|
---|---|
Location | Zhejiang,China (Mainland) |
Year Established | 2002 |
Annual Output Value | |
Main Markets | Central America 7.04 Northern Europe 6.03 Southern Europe 6.53 South Asia 3.02 Domestic Market 5.03 North America14.05 South America 8.04 Eastern Europe7.04 Southeast Asia 6.03 Africa6.03 Oceania 7.04 Mid East 6.03 Eastern Asia 8.04 Western Europe 10.05 |
Company Certifications | ISO 9001:2008;ISO 14001:2004;CE;CE |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | 51% - 60% |
No.of Employees in Trade Department | 6-10 People |
Language Spoken: | |
b)Factory Information | |
Factory Size: | 3,000-5,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered Design Service Offered |
Product Price Range |
Send your message to us
Mini Valve, Mini Needle Valve
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 50 Pieces pc
- Supply Capability:
- 50000 Pieces Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords