Instrumentation Valve Instrument Valve Needle Valve
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 3000 Pieces pc
- Supply Capability:
- 1,000,000 Pieces Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications of Instrumentation valve/Needle valve
we can supply various instrument valves, size from 1/8" -2", connection NPT, BSP,ISO thread, FD-LOK tube fitting, material SS316.
Instrumentation valve/Needle valve
orifice :4mm
pressure up to 10000psi
temperature up to 400oC
approximate weight:0.55kg
OEM orders are acceptable
Product: Valve Aerosol Cap
Mounting Cap:aluminum
Stem:plastic / metal
1) Metering (35ul 50ul 75ul 100ul 120ul and 150ul)
2) Continuous
Dip tube:according to the length of can
- Q:Is the injection pressure tight after the valve pin closes?
- In the process of injection molding, solution and shrinkage because of cooling, but because the screw to move slowly forward, so that the material in the tube to melt into the cavity, to supplement the needs of shrinkage, called pressure. It means to prevent product shrinkage, with pressure if production is stable. The pressure can also adjust the product size, without weld line
- Q:I put the motorcycle carburetor electronic enrichment valve needle hole is blocked, there is no harm
- When the cold car starts, the concentrated valve can provide a thicker mixture for the engine, and the automatic air door is used for starting the cold vehicle. Blocked to start
- Q:After the needle valve sealing, how to solve the cold material?
- In general, plastic parts should be set at least three or four shots to be more scientific.
- Q:Needle valve hot runner Road, needle valve does not move, what are the reasons?
- Then heat the drain plate and remove the needle from the distributor with the needle sleeve. Then the muskets firing valve needle sleeve, the glue burn clean, it can take out the needle valve. Hope to help you.
- Q:How can I see a needle valve in plastic products?
- The needle tip of the valve will also have obvious marks, because the high temperature and the entrance of the glue hole will always be more or less bright or rough than that of the die steel.
- Q:How long is the needle length of the needle valve?
- This problem is hot runner companies should pay attention to the problem, they will be based on the mold drawings to define the length of the needle, thickness and so on
- Q:What's wrong with the sealing ring at the needle valve of the spray gun?
- If the sealing ring break not leak does not affect the pressure, spray a shares is because the last time you painted not wash or spray gun, the valve needle sharp deformation, if often run out of the gun after cleaning will cause the spraying effect is not good, long lance clog, preferably after use with clean water that day!
- Q:Mold glue is how the air valve needle
- The hot plate of the needle valve has operation instructions on it. If it is not clear for a long time, see if the hot runner leads out the interface. Is there any mark gas IN/OUT?If not, (usually two groups, only one group and one group)
- Q:Does the needle valve hot runner have adhesive problems? What are the possible causes?
- ExistingWe asked coreter hotrunner maintenance customer servicePossible reason: the valve needle does not emit too much heat.Handling: reduce hot nozzles and gatesThe temperature increases with cooling time.
- Q:Hot runner valve needle in the molding, why will retreat?
- The following reasons may cause the needle to recedeThe plastic pressure is greater than the cylinder pressure, causing the needle to recede
1. Manufacturer Overview |
|
---|---|
Location | Zhejiang,China (Mainland) |
Year Established | 2002 |
Annual Output Value | |
Main Markets | Central America 7.04 Northern Europe 6.03 Southern Europe 6.53 South Asia 3.02 Domestic Market 5.03 North America14.05 South America 8.04 Eastern Europe7.04 Southeast Asia 6.03 Africa6.03 Oceania 7.04 Mid East 6.03 Eastern Asia 8.04 Western Europe 10.05 |
Company Certifications | ISO 9001:2008;ISO 14001:2004;CE;CE |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | 51% - 60% |
No.of Employees in Trade Department | 6-10 People |
Language Spoken: | |
b)Factory Information | |
Factory Size: | 3,000-5,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered Design Service Offered |
Product Price Range |
Send your message to us
Instrumentation Valve Instrument Valve Needle Valve
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 3000 Pieces pc
- Supply Capability:
- 1,000,000 Pieces Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords