YM-1309 10W LED Mini Moving Head Beam Light

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
10 kg
Supply Capability:
800 kg/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Lamp:10WLED Mini Moving Head Beam Light
Voltage: AC220V 50HZ
Light source: 1 * 10WLED
Power: 30W
Color: White OR RGBW 4IN1
Run mode: Auto, DMX512, master-slave
DMX channels: 9CH/12CH
Package Size: 28 * 21 * 23cm
NW: 3KG
 

GW: 3.5KG

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to program the head light?
1, for each lamp programmed address code, in order to make sure it is a few lights. 2, according to the lamp console instructions, programming can.
Q:Stage equipment, 408 console, how to control waterproof PA lamp, shake head lamp, who knows?
Voltage / frequency: 220-230V/50-60Hz or 110-120V/50-60Hz, power: 10W.Features: can control 16 channel 32 computer lights, backlit LCD display.8 channel handles with page key control, 16 channels, 1 speed keys, 1 keys connected.1400 step storage capacity.36 program, each program up to 99 steps. Each step speed, gradient the parameters set independently. In cooperation with the push of the lights go rate, the time step can range from 0.1s-60s.32 can directly call the computer lamp scene. Can run 4 program, 32 different kinds of computer scene at the same time. The precision of X/Y control.16Bit lamp X/Y lamp by computer data wheel control unity. Off data retention.
Q:Shake head light, address code and console consistent, but not controlled, the address of this table lamp code for other lights
3. signal amplifier has a problem, (the general returned to the factory maintenance) lamps have a Kalong (such as card head and seat Kalong bad; some lamps qalun seat specially there is a piece of circuit board, there are 2 zener diodes), if they can also cause bad pull out of control) signal line between the 5. seat and the circuit board Kalong 6.SN75176IC problem with bad contact problems, so that the signal into it without output to the input pin of the main chip (CPU) 7.CPU main chip problem is not available, the received signal has 8. address code, or dial and switch problem is invalid. Another case is connected to the console signal lamps back without rules run into chaos, unplug the signal line can be a general signal line reverse pull (signal line in 3 small lines) have a switch or turn back, you can pay attention to the normal work of 9. seat Kalong mobile performance, the inside of the connection is broken, the short circuit will cause the lamp is not controlled or abnormal operation, interference, such as: if the ground three signals in the lamp is easy to pull off the interference of
Q:How can I edit a nice shake head lamp and walk the light effect?
With a built-in program console control, the general console is not good, see how others make up
Q:DMX512 how can you shake the head light?
1 check whether the line intact 2 ballast 3 trigger 4 lamp feet 5 thermal relay is intact
Q:240 console, how can I get it, PA lamp, shake head lamp, run simultaneously
Will be different lights address code separately, programming time, a good address code lamps, and then another address code lamps, running time is running at the same time
Q:How many channels are there in the head lamp 1200?
Shake head lamp 1200 has many kinds, commonly used has 12 channels, 16 channels, 18 channels, 24 channels. It depends on your own needs.
Q:200, w beam, shake the lamp, how to change the bulb?
Are basically the same, the two shell open, tail lamp bulb, undid the screws, to take no bubble, for a new good, don't drag the wire, when the bulb into the bulb that try to tilt, slide into the socket, the wick don't touch other things.
Q:Can the LED PA lamp and the shake head lamp be used at the same time with a 512 console?
Yes, but the total number of channels for your head light and LED light should not exceed 512 channel values, such as 16 channel computer light and 8 channel LED PA lamp.
Q:Who will set the DMX512 keyboard is to control the shake head lights hurry ah?
DMX-512 programming instructionsTurn on the power1, open the power supply, wait for about 5 seconds to show "101", press the "program" button for about 3 seconds into the programming state, corresponding to the digital screen "program" indicator light flashing;2, press the "bank" button up and down to select the program number to edit;3. Select the light number to control. Press the numeric key under "scammers";4, set the lamp the function of the data (i.e., push "scenes" under the fader to the desired position);5, press the "midi/add" button, and then press the "scenes" under the 1 key, the surface of the board all the flashing a few times, such a scene is set up;6, choose to control the lights, press the "scammers" digital key below, the function setting lamp data (i.e., push "scenes" under the fader to the desired position), click "midi/add" button, click the "scenes" followed by 2... 8 keys, each program can be compiled 8 scenes, compiled by the "program" button, about 3 seconds to exit the programming state, the program will automatically store.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range