Q:304 stainless steel gasket, how sealed?

Therefore, the 304 stainless steel gasket made of this material, it is generally in the case of metal winding pad, in the 304 stainless steel wrapped on a layer of graphite material or PTFE material,

Q:What's the difference between the gasket and the washer?

Other uses are used as spacers, springs (Baer, gasket, wave washer), wear-resistant pads, pre display devices, and locking devices. Rubber gaskets are also used on taps (valves) to cut off flowing liquids or gases. Rubber or silicone gaskets are also available to reduce vibration of the fan. Usually the outer diameter of the gasket is about two times the inside diameter.

Q:It is urgent to have a spring self sealing ring. The detailed parameters will be listed in picture form, and the quality will be better

Spring self sealing ring, such as parameters: outer diameter 36mm, the internal diameter of 21mm, you know the line diameter is 2.5mm; height is 8mm, please ask the number of turns or the pitch is? You'd better attach a physical map.

Q:Can the metal gasket face seal reach 100MPa?

The gasket standard is mainly the following: first, the standard GB/T 4622.1 - 2003 gasket spiral wound gasket classification GB/T 4622.2 - 2003 spiral wound gaskets for pipe flanges size GB/T 4622.3 - 1993 GB/T 9126 specifications of spiral wound gaskets for pipe flanges - 2003 non metallic flat gaskets size GB /T 9128 - 2003 steel pipe flanges with metal.

Q:Question: a position on the sealing position of copper gasket

Copper gasket seal, high pressure resistance, oil resistance, high heat resistance, long life.

Q:The engine cover, or valve cover, cylinder head cover, the cover is the engine.This is my graduation project... The NASTRAN is used, but the rest of the software is basically the same.Hope to have experienced master Zhidianmijin ah.At present, only 12 order free modal analysis is performed. The final is to do static strength, sealing. The details of the process are not clear. For example, how does the bolt hole bind? Does it hold all the points on the inside surface? What about the boundary conditions and loading? It has more than ten bolt holes, one ring gasket, and 120 0.7bar pressure inside. The material is engineering plastics.Or some people know the whole process from modeling to the results of the general steps to say, you can, thank you first. OK, add more. StopFrequency response and transient response are currently being done

You have a lot of problems in this, and other people to advise you, it is also quite troublesome ah. I suggest that I try my best, try some specific questions and ask questions, so it will be better!

Q:Cleaning the injector without replacing the gasket. Now the car is not ready to strike. What's the reason?!The spark plug 4 has been replacedBattery is not missing!!!When hitting the car, in the taxi will be very good, there will be no good spark phenomenon, when put in a few hours later, in the ignition, there is a bad spark phenomenon!!!Dongfeng Honda civic EXI 1.8AT

Oil leakage of injector or pressure relief of oil pump. After a pause, the inlet air mixture is too strong, and the oil pressure drops to the bottom.

Q:What is the standard for ASME GASKET?

Shim：The gasket is made of paper, rubber or copper sheet, placed between the two surfaces to strengthen the sealing material and to prevent the leakage of the fluid from the sealing element between the static and closed covers.Gaskets (gasket) are mechanical seals between two bodies, usually used to prevent pressure, corrosion, and natural heat expansion, cold contraction and leakage between two bodies. Because machined surfaces are not perfect, gaskets can be used to fill the irregularity. Gaskets are usually made of sheet materials such as cushion paper, rubber, silicone rubber, metal, cork, felt, neoprene, nitrile rubber, fiberglass or plastic polymers (such as Teflon). Gaskets for specific applications may contain asbestos.

Q:Good quality seals, which have, specializing in the production of rubber gaskets?

Hebei Qinghe Tianyu plastic products factory is a professional, they do the rubber seal (seal), manufacturers of large scale, long life, and has many large car manufacturers for many years, they have shown some online pad, other styles can be customized, contact with manufacturers and the Internet are very detailed.

Q:Metal winding gasket, metal tooth shaped gasket, reinforced graphite gasket, metal coated gasket, thank you prawns

Cixi East German sealing material factory, Cixi East German sealing material factory is a company specializing in the development, manufacture and sale of fluid sealing products, as well as the integration of technical services and professional sealing products.The company production of various kinds of fluid sealing materials and products, the main sealing packing, sealing gasket and seal materials three series of products, such as graphite packing, aramid packing, carbon fiber packing, PTFE packing, metal gasket, spiral wound gasket, graphite reinforced gasket, graphite cut gasket, PTFE gasket, asbestos gasket, non asbestos gasket.