Q:How to connect the signal butterfly valve?

If you mean the signal of fire water supply system, there are generally three outlets, one public, one open and one off. Fire control system signal butterfly valve is normally open, so the signal butterfly valve to open position, with a multimeter to measure the 2 lines, the 2 lines into the input module is fine.

Q:What is the difference between wafer (flangeless) type and LUG type of butterfly valves?

WAFER butterfly valve is the valve is divided into LUG (ears) with and without LUG, ordinary LUG without clip on 12 points in the direction of valve is generally two to four bolt holes was not, whereas the LUG of butterfly valve cross dispersed in a circle. Bolt hole. With LUG all bolted through the LUG, so that the butterfly valve and the clamp on the two flange connection is more solid, you check the valve picture, it is easy to understand

Q:What does the butterfly valve D361H - 25C DN350 mean?

Corrigendum: correct type: D361H-25 DN350Should not have C, nominal pressure above 1.6MP carbon steel valve material code name should be omittedValve: central vertical plate welded turbine butterfly valve, nominal pressure 25kg, caliber 350mm, body material, carbon steel, sealing surface material: Cr13 stainless steel

Q:What does the model D373H-16C of butterfly valve mean?

D373H-16C said: D type butterfly valve butterfly valve 3 said, said 7 of the turbine, said clip, 3 said the three eccentric (swash plate), 16 C nominal pressure, said carbon steel. In fact, if you want to understand this, to understand the valve 3.07ghz, later met have to be attached to the valve. 3.07ghzModel for valves, valve number indicates valve type valve should normally be that type, drive type, connection type, structural features, nominal pressure, sealing surface material, body material and other factors. Standardization of the valve type of valve design, selection, distribution, provide more convenient. The type of valve types and materials are more and more more models of the preparation of the valve will become more and more complicated. Although the preparation of our valve type unified standard, but gradually can not meet the needs of the valve industry. At present, the valve manufacturer usually adopt a unified numbering; not uniform numbering, the manufacturer can make out no.methods according to their own situation. Unit two unit three unit four unit five unit six unit seven unit

Q:I went online to check where was the pcv valve for a 2001 ford focus, but I didn't find it. Does anyone have a picture? Thanks

Go around to the passenger side of the car and shove your arm way down along the firewall behind the engine. Feel around with your fingers and you will feel the PCV hose where it connects to the intake. Once you have found that you can follow it forward from underneath (no kidding) about a foot to the PCV valve. I don't think it is even visible from the top.

Q:How can the flange butterfly valve be installed on the pipe?

Outlet pipe configuration.If in the pipeline, the valve in order to do not bear the direction of the force and bending moment, it is best to set the valve at the exit side of the expansion joint. Valve opening and closing valve water pressure should not be borne by the foot, but through the valve flange, by the pipeline to bear as well.Butterfly valve structure is generally shorter length, and its butterfly plate will be extended to adjacent pipes or other parts, so be careful not to collide with other parts and interference. And to prevent the error matching pipe diameter greater than C and collide with the butterfly plate.Butterfly valve as a regulator, just adjust the flow and pressure. The valve is regulated by loss of pressure.

Q:D37A1X9-16CB1: what does this butterfly valve mean?

The model is composed of 7 units, the types of valves (gate valve Z, J, L, Q ball valve, throttle valve, check valve and H valve, butterfly valve, connection mode (D) internal thread 1 thread 2, welding flange 4, 6, 7, the clamp (0) electromagnetic transmission mode 1 solenoid valve, hydraulic, electric and hydraulic turbine are 2, 3, 4 and 5 gears, bevel gear, pneumatic hydraulic, 6, 7, 8, 9) pneumatic and hydraulic, electric, structure (straight or DC type 7,1 on behalf of the center plate, vertical type A (A) and LT X9) on behalf of a sealant is heat-resistant rubber, kg 16 kg, C represents the body material of carbon steel WCB, B1 on behalf of the valve plate is made of ductile cast iron plating)

Q:The water supply pipe is the gate valve And on the cross dry pipe are the gate valve? To answer the 30

1, this is a good question, it seems that this has not yet made a unified standard requirements, a bit confused2, personal understanding of fire water supply pipe, pipe shall be installed on the valve, because the valve is fully open all closed features of fire control system is usually required is fully open, easy management features are obvious.3, fire water supply system is also useful to butterfly valve, but mainly signal butterfly valve.The signal butterfly valve is generally installed in two parts: floor level, dry pipe, flow indicator front end, trunk pipe, wet alarm valve, front end.Floor level pipe installation is a function of the signal valve, when the floor spraying system needs repair, close the valve, open the end of the floor drain, emptying the water in the spray system, maintenance; two is the sprinkler system is not allowed inside water, when the butterfly is closed, will transmit a signal to the the fire alarm system, fire alarm system receives a monitoring signal (so called signal butterfly valve), fire sprinkler system that the floor is anhydrous state, fast repair.Wet alarm valve at the front of the signal butterfly valve with the main floor of the main role of the butterfly valve, first, maintenance, and two is the prompt sprinkler system, there is a signal butterfly valve closed, should be repaired as soon as possible.

Q:Butterfly valve in the use of the difference? Caliber?

Role of butterfly valveButterfly valve is to use disc type to open and close parts reciprocating reciprocating about 90 degrees to open, close or adjust the flow of medium valve. The butterfly valve has the advantages of simple structure, small volume, light weight, material consumption, installation of small size, the driving performance of torque is small, simple operation, rapid, high chemical corrosion, and can also have good flow control function and closure characteristics, the use of butterfly valve is very extensive. Its varieties and quantities are still expanding, and the development of high temperature, high pressure, large caliber, high sealing, long life, excellent regulation, as well as multi-function development of one valve. Its reliability and other performance indicators have reached a high level. Disadvantages, there is a certain resistance to the medium.Gate valves are more used in steam pipes and large diameter water supply pipelines, because of the general requirements of fluid resistance is small, the use of gate valve.Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open. Need a higher installation space, the valve sealing surface has a certain self sealing capacity, its spool by the media pressure closely with the valve seat sealing surface contact, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.

Q:I have 1993 Seville 4.9. I got a new EGR valve but it didn't help. I tested it with vacuum pump, it won't hold pressure at all, same with old one. Is that new EGR valve bad or just different type of EGR that vacuum pump won't work? Thanks!

Did you get that EGR valve from Cadillac dealership?? A lot of those aftermarket parts DO NOT LIKE Cadillac's!!!!!!!!!! I run into that all the time nor will we use any aftermarket parts due to the problems we have with them. Make sure that switch is working that controls the EGR valve. I have seen those fail also. You need access to a serive manual so you can command that switch on off check with a test light a vacuum gauge to make sure you are getting vacuum to that EGR Valve. Also, make sure that the ports are not clogged up with carbon, even check the pipe inside the throttle body opening, they should be clean inside those tubes !!!!!!!!!