Single Mast Aerial Work Platform--AMWP6/AMWP7.5

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Single Mast Aerial Work Platform

AMWP

1KG=2.2LB 1INCH=25.4MM

Model No.		AMWP6	AMWP7.5
Max.Platform Height	mm	6000	7500
Working Height	mm	7800	9300
Max.Travel Height	mm	6000	6000
Stowed Height	mm	1980	1980
Min.platform Height	mm	510	510
Ground Clearance	mm	50	50
Max.Work Load	kg	150	125
Platform Size	mm	630x760	630x760
Max.Drive Speed (Platform Stowed)	kph	2.4	2.4
Max.Drive Speed (Platform Elevated)	kph	0.8	0.8
Tuming Radius		0	0
Max.Travel Grade		20%	20%
Driving Wheel	mm	Φ230~250x80	Φ230~250x80
Caster	mm	Φ200x50	Φ200x50
Charger		10~12A	10~12A
Phthole Protection System		Automechanism	Automechanism
Overall Length	mm	1360	1360
Overall Width	mm	790	790
Gross Machine Weight	kg	1000	1025

Q:Can the stepping motor drive the hydraulic platform?: Are you a driver for this motor? But the normal step motor is only for torque, step Angle, phase number, not for rotational speed; It may be a servo motor or torque motor, and if the speed is low it is the possibility of torque motors. In addition, you can measure the current, voltage or waveform below.

Q:To make a four trapezoid screw lifting up seven tons of lifting platform should be matched with the straight screw and motor: Can be judged according to the accuracy requirement of lead screw grinding or rolling, depending on the load and its acceleration can choose servo power right away and screw the maximum load capacity (do longer engineers can intuitive judgment the diameter of the screw and large), so that you can around the power of the servo motor of the different speed and different lead screw to match, so there will be several different schemes: high speed servo motor with small lead screw (sometimes deceleration machine), big inertia servo with lead screw. Under the condition of the machine cost to determine, from two to three scheme choice, choice of method is to choose low cost, with high stability, cost effectiveness and cost are the same common and suppliers have a spot. If the single from choose the ways of the servo and screw usually have an intuition, like 3000 revolutions of servo goods on the market the most sufficient, screw is according to the supplier's inventory.

Q:Diablo ii flame volcanic mission will not be able to jump: Go to the end of the board and move to the top of the board, then move to the opposite side of the position, shift the shift and then move the space.

Q:What is the phenomenon of the worker's transport of wood using a lift: Imobile elevator accessory device can be configured for any combination, such as lifting capsules can be used with the inward and outward transportation equipment, make fully automated conveying process, operators need not enter the elevator, so as to ensure the personal safety of operators, and can realize the goods transport between floor, to improve the production efficiency; Electrical control mode; Work platform form; Dynamic form, etc. Limit the function of the elevator to achieve the best use effect. Imobile elevator optional configuration of hydraulic power, convenience and the surrounding the lap joint of frame, roller rolling or motor, prevent pinches safe touch, organ type safety guards, moving or motor rotary worktable, hydraulic flip table, to prevent falling elevator safety support bar, stainless steel security guard network, power system of electric or hydraulic elevator walking, mesa of ball. A stationary lift is heavy in weight. It's not affected by the environment.

Q:The hydraulic cylinder with hydraulic platform is changed to whether the cylinder is feasible: As long as your cylinder size is large enough, theoretically! But in practice, it's not feasible to think about space and so forth.

Q:Which is good for mobile goods elevators?: Everyone knows that a penny a points goods, jinan economic brands cargo-lifts, although is not the lowest market price, but the interior of the lift platform all electronic components is a product of the military level,

Q:What happened to the rise and fall: The motor is missing (the motor is not moving, and there is a buzzing sound) to check the circuit breaker and the electrical wiring. The drop valve is open when the drop button is released, and the voltage meter is used to check if the valve has electricity. If there is no electricity, check the line and troubleshoot it. If there is electricity, the valve itself is out of fault. The slide valve must be clean and flexible. The overflow valve is adjusted to the relief valve. Under 100% rated load to adjust the oil level is too low, the oil pump hydraulic oil filled up at a empty absorption, oil absorption filter clogging, clean filter, oil leakage, check the suction tubing and connectors; Tighten the joint.

Q:What is the reason for the automatic lowering of the hydraulic platform: The overflow valve opens and closes and is not properly closed, and checks for leaks.

Q:Safety operation of hydraulic platform: 4, rise and fall: press the "rise" button, start the motor, the motor spin, the hydraulic system work, the oil cylinder protruding, the platform rises. Stay up to work the required height, "stop" button, the motor stop lifting platform, can work, if not in accordance with the "stop" button, the platform to calibrate height be 8 meters (native) trip switch, platform in height. At the end of the work, press the "drop" button, the solenoid valve action, when the oil cylinder is turned on, the platform is lowered by itself. During the use of hydraulic platform, it is strictly forbidden to overload (the unit load is 300kg), and the operator on the platform will not be moved during the descent. When moving or traction hydraulic platform, the supporting leg should be collected and the platform will be lowered to the lowest position. 7, when platform malfunction cannot work normally, should be promptly cut off the power supply for repair, it is strictly prohibited to equipment to work, in spite of non-professional workers do not remove the hydraulic components and electrical components. Do not use the machine in an unstable condition on the ground. Please do not raise the platform without the platform, the outside legs are not adjusted, the platform is flat and the ground is unstable.

Q:Hydraulic platform repair work instruction book, trouble which big man helps to provide: Jinan zhihua elevator machinery co., LTD. Is specialized in the production and development of a unit hydraulic elevator for the oil and oil. The lift is raised all the way up. In this position, the hydraulic pressure should be 40 to 50 mm above the bottom of the box. Hydraulic oil is a variation of dark, sticky or grit, such as a discovery should be replaced in time (32 # hydraulic oil) The lift is maintained every year Check all hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range