Roll forming puching automatic machine GY
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
The production line consists of decoiler, leveling device, punching unit, roll forming M/c, straightening device, moving cutter, hydraulic system and PLC system.
It could be applied for various production with puching demand.
Decoiler carry coil at the start of the production line and open uncoil it for next process. Tonange of it depends on specific requirement.
Leveling device make the sheet leveled before rolll forming, with pinch roll and leveling rolls
Puching unit punch holes as required before roll forming, it's controlled by PCL system.
Roll forming M/c roll form sheet into profiles with necessary roll forming stations. By adjusting roll for different profiles production.
Straightening device is used to traighten the profile after roll forming, to keep finished profile as required.
moving cutting device cuts profiles with non-stop of the production line.
PLC control each device and whole line.
- Q:What is the surface rolling forming machine process?
- Due to the rolling surface of metal plastic deformation, so that the surface microstructure of cold hardening and grain refinement, forming a dense fibrous, and the formation of residual stress, hardness and strength, so as to improve the surface wear resistance, corrosion resistance and compliance.
- Q:Improvement in rolling forming process
- Can not meet the slender rod, thin-walled tubes and other rigid parts of the processing.
- Q:A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- According to my experience, there should be a problem with the boot encoder (also known as the digital wheel). Thank you. I hope I can help you.
- Q:What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Use 40Cr or 20Cr, Cr12.Cr12MoV, quenching and tempering treatment, think of hardness, high point, carburizing, nitriding, and consider adding lubrication device to extend its service life
- Q:Process mould for rolling forming process
- A movable wire plate, made of the same fixed wire plate, for relative reciprocating motion. Roll forming is the design of different structures on the plate rolling on the workpiece. Roll out all kinds of thread, convex ring, knurling, end chamfering, groove with different width and thickness as well as other required shapes.
- Q:What is rolling forming processing?
- Rolling process is a kind of pressure finishing, which is a kind of cold plastic characteristic of metal under normal condition.
- Q:Material and equipment for roll forming process
- Rolling process is a cold forging process, which can be used for rolling and forming a lot of materials. Among them, low carbon steel is a material commonly used in rolling forming, and non-ferrous metal is more suitable for roll forming.
- Q:Introduction of roll forming process
- With the progress of technology and the development of production, more and more attention has been paid to the roll forming process.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Roll forming puching automatic machine GY
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products