Best Quality for Metal Roof and Wall Panel Forming Machinery
- Ref Price:
-
$15,000.00
/ set
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 set set
- Supply Capability:
- 100 Set per month set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Gerenal Information of Metal Roof and Wall Panel Forming Machinery
This machine is for producing wall panels, the max forming speed is 15 meters per minute. We can design and produce according to different drawings.
Working Flow of Metal Roof and Wall Panel Forming Machinery
Decoiling the sheet---- Sheet guiding----Roll forming---- Pressing the panel ----Measure length ----Cutting the panel----Panels to the supporter
Technical Data of Metal Roof and Wall Panel Forming Machinery
A: Power Supply:
380V, 3 phases, 50 or 60 Hz (can be adjusted according to actual power supply conditions in different countries)
Main motor power: 5.5KW
Pump power: 5kw
B:Uncoiler:
Inner diameter: 500mm
Outer diameter: 1100mm
loading weight: 5t
C:Forming Part:
Feeding thickness: 0.3-0.8mm
Feeding width: 1220 mm
Forming speed: 12-25m/min
Cutting Deviation: 10m±2mm
No. of Roller station: 11-18 groups
Roller material: Cr12
Material of shaft: 45# steel with heat treatment
Diameter of shaft: 60-110mm
D:Hydraulic System:
Hydraulic pressure: 12-30 Mpa
Cutter material: Cr12
E:Control system:
Full-automatic NC-PLC control system
Control channel: Colored touch screen
- Q:What is the surface rolling forming machine process?
- Due to the rolling surface of metal plastic deformation, so that the surface microstructure of cold hardening and grain refinement, forming a dense fibrous, and the formation of residual stress, hardness and strength, so as to improve the surface wear resistance, corrosion resistance and compliance.
- Q:Improvement in rolling forming process
- Can not meet the slender rod, thin-walled tubes and other rigid parts of the processing.
- Q:A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- According to my experience, there should be a problem with the boot encoder (also known as the digital wheel). Thank you. I hope I can help you.
- Q:What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Generally speaking, to consider the use of rollers in the requirements, including: 1., good wear resistance, 2. toughness, 3., high hardness, 4. hardened layer (easy to wear after repeated repair)
- Q:Process mould for rolling forming process
- A movable wire plate, made of the same fixed wire plate, for relative reciprocating motion. Roll forming is the design of different structures on the plate rolling on the workpiece. Roll out all kinds of thread, convex ring, knurling, end chamfering, groove with different width and thickness as well as other required shapes.
- Q:What is rolling forming processing?
- A special rolling tool is used to exert certain pressure on the surface of the workpiece so as to make the surface metal flow.
- Q:Material and equipment for roll forming process
- Rolling process is a cold forging process, which can be used for rolling and forming a lot of materials. Among them, low carbon steel is a material commonly used in rolling forming, and non-ferrous metal is more suitable for roll forming.
- Q:Introduction of roll forming process
- With the progress of technology and the development of production, more and more attention has been paid to the roll forming process.
1. Manufacturer Overview |
|
|---|---|
| Location | Hebei, China |
| Year Established | 2008 |
| Annual Output Value | |
| Main Markets | 28.71% Domestic Market 16.39% Eastern Europe 14.26% North America 14.26% Southeast Asia 14.26% Africa 7.13% South America 4.99% North America |
| Company Certifications | ISO9001:2008 |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | Tianjin Port |
| Export Percentage | 41% - 50% |
| No.of Employees in Trade Department | 8-10 people |
| Language Spoken: | Chinese; English |
| b)Factory Information | |
| Factory Size: | 10,000-30,000 square meters |
| No. of Production Lines | Above 10 |
| Contract Manufacturing | OEM Service Offered |
| Product Price Range | Average |
Send your message to us
Best Quality for Metal Roof and Wall Panel Forming Machinery
- Ref Price:
-
$15,000.00
/ set
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 set set
- Supply Capability:
- 100 Set per month set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
