Packing and Lamination Film-9mic Aluminum Foil/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
Product Structure
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
● Aluminum foil – LDPE
● Aluminum foil- PET- LDPE
● Clear Transparent PET-Aluminum foil – LDPE
● Aluminum foil-Metallized PET- LDPE
● Metallized PET- LDPE
Product Application
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
Product Advantage
Light weight
• High manufacturing accuracy
• High strength
• Small inertia resistance
• Strong heat dissipation ability
• Good visual effect
• High reflective insulation
• Heat resistant, water proof, stable at high temperature;
• Environmentally friendly, no smell and not-toxic;
• Smooth and clear surface;
Product Packing
1. Waterproof paper then PVC shrinking Film
2. Kraft paper only
3. Woven cloth
4. Kraft paper or Water Proof Film then Metal/wooden pallet
5. (Also as your request. )
Product Remarks
1. The data above are typical results and subject to change without notice.
2. Tolerance: Weight and Thickness: ±10%; Width: ±3mm;
Length: Cut Roll & Log Roll ±0.3m, Jumbo Roll ±0.5%.
3. The products should be stored at room temperature and kept from wet and heat source.
4. It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, and free of grease and oil.
5. The user should take test and do trial-application on the above products before coming into application so as to witness and ensure suitability for user’s special purpose and technique.
Product Data Sheet
PROPERTIES | UNIT | VALUE | TEST METHOD |
Basic weight | gsm | 43.5 | ASTM D646 |
Thickness | mic | 33.2 | ASTM D646 |
Tensile strength: M. D. X. D. | N/15mm | 23.5 23.5 | ASTM D882 |
Delaminating Values | N/15mm | 1.5 | ASTM D904 |
Reflectivity of foil surface | % | 95 | ---------- |
Temp. Resistance | -40°C 130°C | No Delamination No Delamination | ASTM C1263 |
Water vapor permanence | ng/N.s | 1.15 | ASTM E-96 |
Product Picture
FAQ
1. What is the product keeping conditions?
The Aluminum Foil Facing should be stored at room temperature and kept from wet and heat source.
2. What is the guarantee years of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
3. What is the delivery time of the order?
In the purchase of product within four working days, we will arrange the factory delivery as soon as possible. The specific time of receiving is related to the state and position of customers. Commonly 7 to 10 working days can be served.
- Q: How much is plastic waste film?
- Waste plastic film is divided into many categories, depending on what material, PP, PE, PET, PVC, all kinds of prices.
- Q: How is the blow up ratio of a plastic film calculated? What's its formula?
- The ratio of film diameter to die diameter in blown film.
- Q: What about the glue left behind the plastic film on the door?
- Apply a little bit of hand sanitizer to the scissors, then dig a small hole with the scissors, then scrape them off slowly and then rip them off with your hands.
- Q: After decorating, how can the plastic film on wooden board be peeled off?
- Rub it off with a hot wet towel and remove it slowly. It is better not to try anything else to prevent corrosion or damage to the furniture surface.Take off a little slower, as far as possible to bring down the whole, and if broken into pieces, it is not good to expose
- Q: Keyboard circuit board, film paper and rubber strip, how is it installed?
- In the side of the conductive thin film circuit and the circuit board finger contact.
- Q: What's the plastic film on the disposable paper cup?
- The wax coated cup is coated with a layer of wax used to separate the water.The polyethylene film cup is the film covered with polyethylene in the cup wall.The wall of the double wall cup has two layers of paper. There is air between the paper and the paper, and the insulation is very good.
- Q: Why are more transparent plastic films used in flower sheds instead of glass?
- The cost of plastic film is low and the cost of glass greenhouse is too high.The plastic greenhouse is economical, practical and low in cost, and can be chosen according to the needs of production and planting. Plastic film is better for profit maximization.Glass greenhouse skeleton is usually made of galvanized steel pipe or aluminum alloy light steel, in the process of cultivation, the service life is the longest, but the cost is very expensive. If the flowers are not special rare flowers, it will not use the glass greenhouse.
- Q: What are the differences between geotextiles and geomembrane?
- The main mechanism is a plastic film impermeable partition dam Water Leakage channel, with its large tensile strength under pressureadapt to dam deformation; and the non-woven fabric is also a kind of polymer material chemical short fiber, through acupuncture or thermal forming, with tensile strength and elongation is higher, it is combined with after the plastic film, not only increases the tensile strength and puncture resistance of plastic film, non-woven fabric and because rough surface, increases the friction coefficient of the contact surface, in favor of composite geomembrane and protection layer stability. At the same time, they have good resistance to bacteria and chemical action. They are not afraid of acid, alkali and salt corrosion.
- Q: Can I use plastic film to make roofing waterproof?
- Not too good, poor corrosion resistance, can be used with waterproof cement tiles (can be thinner, cost saving) if there is a groove with a hose with waterproof ribbon, it has good corrosion resistance and decoration of a long time
- Q: Why should a plastic film be covered after civil construction?What's the point? Do you have any requirements for plastic film?
- The plastic film has no special requirements, as long as the cover to prevent water evaporation. In the cold season construction to cover the mats and other things to keep the temperature.
Send your message to us
Packing and Lamination Film-9mic Aluminum Foil/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
