Mobile scissor plateform(standard)

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:There are different kinds of milling machine and vertical lifting machine milling machine
Start by figuring out the difference between vertical and horizontal The main shaft of vertical milling machine is perpendicular to the workbench, and the spindle of horizontal milling machine is parallel to the workbench. The knife of vertical milling machine is relatively flexible, the scope is wider. Can use vertical milling cutter, machine clip, bit etc. Milling keyway, milling plane, boring hole, etc.
Q:How does the elevator repair
All parts should be filled with lubricating oil to extend the life of the bearing. The oil and oil level of hydraulic oil. The platform rises all the way up, and in this position, the hydraulic pressure should be 40 to 50 mm above the bottom of the box. Hydraulic oil is a variation of dark, sticky or grit, such as a discovery should be replaced in time (32 # hydraulic oil) Annual maintenance A. check all the hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. C. the elevator hydraulic oil is put in the rejected, tighten the joint remove oil filter, after cleaning, use compressed air is clean, and then back into the tank, and the connecting line. (put on new oil and don't keep using the old oil. Otherwise, the moving parts in the system will accelerate the wear and tear.)
Q:What is the price of the hydraulic platform
Mobile I have dozens of it are common, such as 0.3 T - 0.5 T - 3 M price about 15000 yuan 3 M is 18000 yuan 1 T - 4.5 M is 21000 yuan price basic like this, look at your own ability to discount.
Q:The automatic mahjong machine has a lift station always one. What is the other three normal
The synchronous motor is out of control, or the motor is broken by a series of windings
Q:Diablo ii flame volcanic mission will not be able to jump
Go to the end of the board and move to the top of the board, then move to the opposite side of the position, shift the shift and then move the space.
Q:There are several reasons for the hydraulic cylinder oil leak on the elevator
Internal leakage 1) wear-resisting ring on the piston is badly worn, causing friction between the piston and the cylinder liner, and finally pulling the casing, piston and seal. Sealing long term failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) the hydraulic oil is dirty, and a large amount of impurities enter the cylinder to seal the piston seal to the bad.
Q:Does the shear fork lift stand belong to special equipment?
It belongs to special equipment, the manufacturer must have special equipment production qualification "special equipment manufacturing license" to be able to produce the sale shear fork lift machine. The products of the manufacturer without relevant documents are not eligible.
Q:How does hydraulic platform change sealing ring, how to operate
Remove the hydraulic cylinder. Before the hydraulic cylinder is disassembled, the oil pressure in the hydraulic cylinder circuit should be reduced to zero. Remove the parts from the hydraulic cylinder when disassembling.
Q:Who knows the price of a sloping platform?
The platform is lowest, highest, high, and how long it takes to rise. I have a few friends who do this, I can help if I need to
Q:Seven tons of lift should be fitted with the straight screw and motor
Can be judged according to the accuracy requirement of lead screw grinding or rolling, depending on the load and its acceleration can choose servo power right away and screw the maximum load capacity (do longer engineers can intuitive judgment the diameter of the screw and large), so that you can around the power of the servo motor of the different speed and different lead screw to match, so there will be several different schemes: high speed servo motor with small lead screw (sometimes deceleration machine), big inertia servo with lead screw. Under the condition of the machine cost to determine, from two to three scheme choice, choice of method is to choose low cost, with high stability, cost effectiveness and cost are the same common and suppliers have a spot. If the single from choose the ways of the servo and screw usually have an intuition, like 3000 revolutions of servo goods on the market the most sufficient, screw is according to the supplier's inventory.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range