Q:What are the procedures for buying a forklift?

The forklift needs to be registered with the local quality supervision bureau. Required materials: (1) the application form for the use of special equipment (the original one); Each copy of the business license and the copy of the organization's code for the period of validity of the unit of use;

Q:How much oil the three tons of forklifts are for a kilometer

The 3-ton forklift is about 3 to 4.5 liters of oil. Forklift truck is an industrial transport vehicle, which is a variety of wheeled transport vehicles for loading and unloading, stacking and short-range transportation. International standardization organization ISO/TC110 is called an industrial vehicle. Often used for the transportation of large items in storage, usually with a fuel engine or battery. The technical parameters of forklift are used to indicate the structure and performance of forklift vehicles. The main technical parameters are: rated lifting weight, load center distance, maximum lifting height, door frame, dip Angle, maximum speed, the minimum turning radius, minimum clearance from the ground and wheelbase, wheel track, etc.

Q:Electric forklifts can be used for a long time

Look at the use case, look at work environment, look at worker's labor attitude, average about a year and a half.

Q:How many ways to push the forklift truck?

Fuel and electric power. The fuel oil tonnage is big, the power foot, because the burning oil will produce the exhaust gas to the environment the high place is not suitable for use! The relative tonnage of electric power is small, suitable for a small warehouse or clean workshop.

Q:The advantages and disadvantages of exhaust and exhaust in the forklift truck

Imported forklifts are used for exhaust, and of course the cost will increase. The reason is that the height of the exhaust is exactly the same as in the middle of the body, which causes the pollution to spread to the human body, causing damage. The exhaust will blow up the dust of the ground and cause pollution. Are you satisfied with the answer?

Q:People leave the forklift and do what and what to pay attention to when parking

Before leaving the forklift, remove the cargo fork completely, hold the hand brake and remove the key of the switch. Press the emergency isolation switch. If you park the forklift on a slope, you must plug the wheels.

Q:How to solve the oil spill?

Forklifts will run into a variety of problems, affecting both work efficiency and quality of work and causing unnecessary waste. However, before the problem occurs, the failure prevention measures of forklift should have a better effect on the occurrence of the failure. Here's a look at how forklifts can prevent oil spills. Measures to prevent oil spills: carefully dispose of various liners. Be like oil tray or valve cover cover, because contact area is big, not easy compaction, can cause oil leak easily. Tighten the nuts by the repair specification. The underpining of the padding will grease the oil; Too tight will cause the metal to bulge or twist the screw to cause the leak. Timely replacement of failure oil seal. The oil seal is improper, the shaft neck is different from the oil seal, it is easy to dump the oil because of the bias. Some after use for a long time, will lose elasticity, due to aging of rubber sealing lip crack damage or failure, since the tight spring will loss in sealing effect, should be in accordance with the standard repair or replace the qualified parts. Replace the badly worn machine parts in time.

Q:Learn the forklift truck, will you be tired in the future?

Compared to talking about the forklift in the production line, but any job that lasts longer is tiring.

Q:What's the matter with forklift

5) forklift rack and gear meshing clearance adjusting too close, if this is the case, the fault diagnosis and discharge should be removed when the rocker arm in steering gear, if you turn the steering wheel to feel heavy, you should adjust the rack and gear fan, the progress of the screw rod bearing. If it feels unevenly or inside, check the screws, steel balls, pipe clips, rack and bearings without any roughness or damage. Repair or replace when necessary. Ruled out the above failure, forklift can normal operation, should pay more attention to forklift truck is in failure, timely troubleshooting, not small fault assemble into a big failure. All mentioned above is a counterweight forklift driving type steering mechanism, balance weight used in most hydraulic forklift steering, so normally is smaller and lighter. But the same as the material handling tools, electric stacker, electric truck steering system is how China chose, popular models is based on the principle of the leveraged direct mechanical twisting to handle drives the driving wheel reverse adjustment, so very tired very difficult operation. Also, so make working forklift for this kind of fatigue and developed an EPS electronic power steering system, with the motor drives the driving wheel steering, operators only need to turn the handle to realize positioning can be easily. In detail, the electronic steering system principle Outlines of course

Q:Where should I take the special operation equipment certificate for the forklift?

The forklift card shall be the special operation certificate of the quality inspection bureau. You can go to the local quality supervision bureau special equipment department or the special equipment operator training school to take the exam training.