K Series 5-7T I.C. Counterbalanced Forklift Trucks

Ref Price:
Loading Port:
China Main Port
Payment Terms:
Min Order Qty:
Supply Capability:

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:



Load capacitykg500060007000
Power type 

Overall length

(without forks)
Max. lifting heightmm3000  
Load centermm600
Overall widthmm      1995

Overall height

(overhead guard)
mm      2450

Min. turning radius


mm3250 33303370

Max. travel speed

(with/without load)
km/h     26/33
Service weightkg798084609248

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The repair process of forklift inspection
The change of wheel should first be judged when the replacement should be given. For inflatable tyres, the tyre should be replaced when the thickness of the tyre is equal to or less than 1.6 mm. For solid tire, the tire should be replaced when the maximum wear allowance is allowed. This wear measurement is marked by a manufacturer on the side of the tyre. If the forklift truck is used on slippery floor, it should be replaced when the surface of the tyre is less than 1mm. In order to maintain the stability of the forklift truck, it is essential for safe operation forklift, two tires on the same shaft must use the same model of tyre manufacturers and change at the same time. Lift the forklift with a lifting device until the tire is replaced completely from the ground. In addition, when other tires are being replaced, they should be placed under the wheels of the ground to prevent the forklift from sliding. When the pneumatic tyre is replaced, the gas should be released before removing the tire.
Q:How to start a forklift? Say detailed point
Turn the key clockwise and start the engine; First notice the cargo fork: the control lever of the operating door is raised about 300 mm from the ground, and then the door frame is tilted forward to move. Step down the clutch control panel and move forward the back control lever and the gear stop. Slowly release the clutch pedal completely; Forbidding wild driving: don't turn on the key switch when stepping on the accelerator pedal. Do not suddenly start, brake or turn to prevent the fall of the cargo. Don't run over the barriers or obstacles that litter the road. Don't get into the soft ground; When driving on a wet, slippery, uneven or sloping road, please lower your driving speed. Make sure there is a gap between the door frame and the roof and the entrance.
Q:What are some of the common failures of forklifts?
Forklifts cannot be started with the following conditions: 1, the battery without electricity Failure of starter The key switch is bad 4, the oil pump does not supply oil 5, there was no oil tank 6, no oil 7, the crankshaft lock The engine was completely scrapped
Q:The component of electric forklift drive system
Electric forklifts are powered by a battery, an electric controller, a walking motor, and a switch on the direction of the accelerator. The mechanical transmission system has a walking motor, torque converter, differential, axle, wheel.
Q:4 tons of cross-country forklift lifts the four-meter cross-country forklift
Choose the type of forklift fuel for your own condition Internal combustion forklift: suitable for normal operating conditions, outdoor or ventilated conditions and no special requirements for exhaust emissions Advantage: the price is relatively inexpensive, easy to use, long working hours, low environmental requirements, low maintenance requirements and low cost. Disadvantages: large noise and high emissions.
Q:How does the fork of a forklift know that there is no balance
Overload detection is the most important thing. This is the prevention of damage to the goods for deformation.
Q:How does the forklift start?
Why is the front wheel of the forklift narrow.I hope my answer will help you.
Q:What are the traffic rules for forklifts
Safety regulations for forklift trucks The head of the facility shall strictly require the personnel who have received the training and obtaining the certificate to drive the forklift truck. 2. The forklift driver to use checklist to check before, during, and after using forklifts, including all alarm and safety device (see chart), and immediately report to the supervision of a forklift any failure situation; If there is a problem with the brake, you may not use a forklift truck. The trailer or truck for loading and unloading should be put on the brakes and stuck in a block to prevent the car from sliding. Only carry items within the capacity of the forklift. The lifting of the weight is low, and the fork is not more than 8 inches off the ground and leans back. Make sure the load is stable and not tip over when turning.
Q:There is no clutch for the electric cylinder forklift
The way forward of the trolley is simple! Just switch to the electric power supply of the positive and negative terminal! Positive electricity is the way forward, and the other way is back! This is the case for forklifts!
Q:What do you mean by the center spacing of the load on an electric forklift?
The center of load is the center point of a forklift truck. Generally refers to the center of the length of the goods. General forklift pallet fork length of 1.22 meters, then load center on 610 mm, length is 3 meters of the goods if you, the center of the goods on 1.5 m, with 1.22 m goods fork is certainly not possible

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range