Q: Can argon arc welding machine be changed into common DC welder?

The principle of argon arc welding machine and DC welding machine is similar, and all of them are drop characteristics. As long as the solenoid valve high frequency argon arc welding, argon welding and gas off, then the gun switch machine is short circuited, DC welder, welding torch and wire at the same time to swap (with argon arc welding torch grounding wire, grounding wire connecting welding).

Q: What are the well-known automatic argon arc welding machines in the world?

They are all foreigners. Funes. Issa, Ken, Miller. Lincoln. Mega Nick. And has made the sun. Times. Wtl. Welding research and technology, Hua Heng, huayuan. Wait

Q: What causes the DC argon arc welding machine to interfere with the automatic step motor?

The stepper motor driver controls the stepper motor by controlling the pulse. If the drive pulse bandwidth is too wide or the wiring is not reasonable, the control pulse will be disturbed. Argon arc welding produces large electromagnetic interference signals at arcing time.

Q: What about Panasonic argon arc welding machine in Tangshan? Detailed point! Thank you

Matsushita argon arc welding is good, have strengths than the general domestic, molding, arc, arc, good welding

Q: (reallink authentic) inverter DC TIG / arc welder WS-300A how to use the reallink dual-purpose welding?

The home and the same switch or power switch, control switch or adjust the argon arc welding and manual welding, (this switch you can rub on the power to try to understand) two red above should have a word, is to adjust the current size of the welding time (adjust the current size according to your material Bohou),, and the other one is gas (gas delay time delay adjustment switch is used to protect the surface of welding).Is to provide a welding welding power supply characteristics of the electric welding, as simple and flexible reliable, even after welding advantages and parent material and equal strength is widely used in various industrial fields, such as aerospace, shipbuilding, automobile, container etc..

Q: That type of inverter, pulse argon arc welding machine is easy to use

It is made in China and has poor exhaust molding and high failure rate.

Q: What should the novice pay attention to when using argon arc welding machine? (the more detailed the better) thank you!!!

1. connection of input power supplyThe input power of the welder is 380V. Note: before the A. connection, switch the switch of the switch box on the broken position, and connect the grounding cable to the ground at the bottom of the welder. The voltage of power supply network in B. welding machine is single-phase 380V, and the voltage fluctuation of power grid should be in the range of +10%.2. argon arc welding1.) close the power switch, and the power indicator light is on. 2.) switch the function switch to the position of argon arc welding. 3.) welding torch and workpiece. 4.) when welding aluminum, turn the switch down to AC argon arc welding, and then apply welding according to process requirements. When welding the stainless steel, switch the switch to "direct current argon arc welding", and then apply the welding process. 5.) open argon valve, according to process requirements, adjust to a certain flow. 6.) adjust the current knob to the required value according to the process parameters. 7.) the gas delay knob to the required time, welding can be achieved and the requirements of post flow ventilation in advance.3. procedures for argon arc welding1.) switch and check whether the dial knob machine to the correct position; 2.) mobile welding torch, the 2 3mm away from the workpiece position and press the torch switch; 3.) welding process; 4.) loosen the torch switch, welding end valves are closed; 5.) argon, turn off the power switch;4. manual arc welding1.) switch the selection switch to the "general weld" position. 2.) for welding of low carbon steel, the output (+) cathode connected to the base metal, the electrode holder connected to the welder (-) cathode. 3.) with low argon welding stainless steel electrode, the positive electrode (+) electrode holder, the (-) athode metal.

Q: You ask about the quality of argon arc welding machine which brand is good, the requirements of aluminum welding, welding and cutting thickness below 20mm, 12mm can also be used, or DC inverter AC / DC, what model is appropriate, about how much the price, thank you!

Salesman to answer, are deceptive, the market share of the most is the best.

Q: I have a household type 200 inverter manual welding machine. I want to weld stainless steel. Can you change it into argon arc welding machine?

Hard。。 With high frequency circuit, argon welding to hand welding can be very simple

Q: WSM-200A inverter DC pulse argon arc welding machine access voltage, what parts of the assembly damage?

The machine is installed AC input overvoltage protection power source has certain help application (a degaussing resistor and a MYL132D431 varistor) if the short time access "voltage is too large and equipped with about 10A insurance, power supply, welding machine will not damage what, just on the knife fuse will be burned, thus protecting welder but, the fuse is too large, the access time is long, will damage the filter capacitor and even if the bridge, high voltage filter capacitor is not damaged if it might blow pipe field.