Q:I have put a new pressure valve and replaced both thermostat

If it is not overheating due to a stuck thermostat or bad heating element and you changed the TP valve then it is possible you have a problem with thermal expansion. When water is heated it expands and the more it is heated the more volume it will need to expand. Since the water heater and the piping are not designed to expand the water only has one place to go (well two if count the faucet) and that is out the TP valve. This problem is not uncommon and the solution is to have an expansion tank installed on the hot water heater in the piping near the tank.

Q:Butterfly valve D71X-1.6C, DN50, there is no difference between C and no C? What do you mean by "concrete"?

Front is the same, there is C refers to the body of the material is carbon steel, without C, usually refers to gray iron (cast iron is more common, so are generally omitted)

Q:How is the lug butterfly valve connected to the flange?

Lug type butterfly valve is also called a single flange type, that is, with a flange on the valve body, usually installed at the end of the pipe, and even the method is 1: double bolt lock on the valve body 2: into the flange 3: lock nut

Q:What does butterfly valve do?

[1] butterfly valve is also known as turn over plate valve, is a simple structure of the control valve, but also can be used for low pressure pipe medium switch control.[2] butterfly valve: butterfly valve refers to the closure of parts (valve or butterfly plate) for the disk, around the valve shaft to achieve rotation and closing of a valve, the main cut off on the pipe and throttling role. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation. Butterfly valve used in furnace, coal gas, natural gas, liquefied petroleum gas, city gas, hot and cold air, chemical smelting and power generation environmental protection engineering system, conveying a variety of corrosive and non corrosive media pipeline, used to adjust and cut off the media flow. Butterfly valve categories are: handle butterfly valve, turbine butterfly valve, pneumatic butterfly valve, electric butterfly valve and so on.

Q:What's the difference between the three eccentric butterfly valve and the two eccentric butterfly valve?

Single eccentric butterfly valve: extrusion problems, address concentric butterfly valve and valve seat of the resulting in a single eccentric butterfly valve, the structural characteristics of the stem axis deviated from the disc center, so that the butterfly is no longer a rotary bottom plate, axial dispersion, reduce the excessive squeezing and the lower end of the seat of the butterfly board. Double eccentric butterfly valve: in the single eccentric butterfly valve on the basis of further improvement of forming, is the most widely used double eccentric butterfly valve.

Q:Butterfly valve is the control valve?

The flow characteristics of butterfly valves can be approximately equal percentage characteristics, with the positioner can do adjust, is mainly used in large caliber, straight stroke control valve more than 200 volume weight will be great, it suggests using the butterfly valve.

Q:What's the meaning of butterfly valve d371po?

According to the provisions of the JB/T 308-2004 valve type programming method:D== butterfly valve3== transmission: worm gear7== connection mode: clip type1== structure: midlinePo== sealing surface material: lining PoPo== propylene oxide (PO)

Q:Which is better, the round two lobe butterfly valve?

Round type double butterfly butterfly valve is the first choice of Shanghai Machinery & Equipment Co., Ltd., the company is a professional design, manufacture and sale of central air-conditioning products at the end.

Q:The difference between butterfly valve and gate valve

Butterfly valve role, butterfly valve is used to open and close disk type reciprocating rotation of about 90 degrees to open, close or adjust the flow of a medium valve. The butterfly valve has the advantages of simple structure, small volume, light weight, material consumption, installation of small size, the driving performance of torque is small, simple operation, rapid, high chemical corrosion, and can also have good flow control function and closure characteristics, the use of butterfly valve is very extensive.

Q:How to calculate the size of the manual butterfly valve?

[1] type code, transmission mode, connection form, structure form, sealing surface material or lining material, nominal pressure, valve body material, this is the most basic arrangement way now D341X-16C. [2]: butterfly valve also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the air water, steam, and all kinds of corrosive media, mud, oil, metals and radioactive liquid media and other types of fluid flow. On the pipeline, mainly from cutting and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation.