Ductile Iron Butterfly Valve Of Good Quality Made In China
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description:
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images:
4.Manual Wafer Butterfly Valve Specification:
1)Size: DN40-DN1400
2)Material:body-CI/DI/WCB/SS
disc:DI/CF8/CF8M/C95400
3)Professional Maufacturer for more than 10 years
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q:1. What does valve 13Cr&FHF mean? 2, valve WC6 (F11) what does that mean? 3. What does valve P280GH mean? 4. What does valve A335P22 mean?Thank you
- May be non-standard label bar, do not understand, A3 should refer to the body, the material is 13Cr.
- Q:Which industries need valves?
- 3., the other side of energy development is energy conservation, so from the perspective of energy conservation, it is necessary to develop steam traps, and to sub critical and supercritical high parameter development;4., the construction of power stations to large-scale development, so the use of large diameter and high pressure safety valve and relief valve, but also need to quickly open and close the valve;5., for the needs of complete sets of projects, the supply of valves from a single species to more varieties and specifications. The valve required for an engineering project is growing with the full availability of a valve manufacturer.In the next few years, the overall trend in demand for the valve for the upward trend, the valve of this large volume of industrial supplies, its demand in steady growth. Among them, the demand for a larger number of valves in turn are: ball valve (15.5%), cut-off valve (12.9%), safety valve (12.5%), gate valve (12.5%), butterfly valve (10.6%), regulating valve (8%) and check valve (6.1%).
- Q:There is a rectangular hole in the valve core, which the heating company repairman gives to the bolt. Rest assured, I do not want to heating, but my indoor temperature is low, I suspect that the repairman mischief, deliberately give me lower temperature
- The valve has a device resembling a cylinder lock without a dedicated key. However, your home heating is not hot, the valve does not have much relationship. As long as the hole on the valve is parallel to the pipe, the valve is fully open.
- Q:What valve is the FCV?
- It's FCU, Fan, Coil, Unit, fan coil valves
- Q:The low pressure in our factory is below 1.6Mpa, medium pressure is 2.5-6.4MPa, high pressure is 10-80MPa.Where's qusetion:1.6-2.5Mpa??? Which section does it belong to?. I think many of them are defined on the Internet But I didn't say, where's 6.4-10Mpa?
- Valves are classified by pressure:Vacuum valve - valve with operating pressure below standard atmospheric pressure.Low pressure valve - nominal pressure PN is less than 1.6MPa valve.Medium pressure valve - nominal pressure PN 2.5~6.4MPa valve.High pressure valve - nominal pressure PN10.0~80.0MPa valve.Ultra high pressure valve - nominal pressure PN greater than 100MPa valve.Pressure values are the only indicators that distinguish these valves.
- Q:What valve is the YQZ45X-16Q?
- Specifically, YQ usually is the enterprise code, Z valve, 4 representative flange, 5 representatives of the dark bar, X (soft) rubber seal (gate coated with rubber material), nominal pressure 16 representative (PN) 1.6Mpa, Q on behalf of the valve body is made of ductile cast iron. If you add the valve bore (DN), it will be more detailed.
- Q:What does "1/2" mean on the valve?
- 1/2 on the valve indicates that the ends of the valve are 1/2 inches in diameter.Valve is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves (201, 304, 316), chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..
- Q:What does the whole copper valve mean?
- The whole valve is made of copper material. In addition to the ceramic core.
- Q:Why is copper used in cryogenic valves?
- Copper, which is rarely available, is easily deformed at low temperatures and is much more WCB or WCC.Below -46 degrees C, SA352, LCB.LCC
- Q:Valve difference
- Valve difference, or you should ask the classification of valves, valve classification, there are several sub methods, some according to the model, and some are by use, then each kind of valve is divided into several categories and models. Take the trap for example, it is a kind of valve, and then it is divided into steam traps, air traps, float traps, and so on. If you really want to know the difference between the valve you search the Internet under the classification of the valve, there are a lot of articles, or you directly to the trap inside www.ssfmsh find an article on the valve type article, can not give you a specific address, is not allowed here. You work hard, go find kazakhstan. I hope my answer will be helpful to you.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Ductile Iron Butterfly Valve Of Good Quality Made In China
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords