Q:What are the ten major brands of China's valves?

1. fine fine group valve Co., Ltd.2. Zhuzhou Southern valve Limited by Share Ltd3 Chinese KaiWeiXi valve group4 the Sufa technology industry Limited by Share Ltd5 Zhejiang Chaoda valve Limited by Share Ltd6. Sichuan Zigong high pressure valve Limited by Share Ltd7. 、 Shanghai Valve Manufacturing Co., Ltd.8. Guangdong Mingzhu group Limited by Share Ltd9. three flower holding group10 Shanghai Valve Factory Co., Ltd.

Q:What is called protective valve, and other valves what is the difference?

Protection valve should be in the air defense valve, can be copper gate valve. (according to the specific use of civil air defense requirements, design institute does not count).2, while the protection valve should be a locking device with the valve, not the general valve can be replaced.

Q:What is a lift rod valve?

Lever valve stem nut in the valve plate, it with the disc (hand wheel) to open the turn, its stem pull the valve head and higher than the valve disk, also known as the bar valve. It is different from the dark rod valve, dark rod valve stem nut in the valve body, when the disc rotates, the stem will not rise.

Q:What is the difference between the adjustable range of valve 50:1 and 100:1?

Adjustable ratio is also called adjustable range, if to R to indicate, then R=Qmax/Qmin should pay attention to the minimum flow, Qmin and leakage of different meanings. The minimum flow refers to the lower limit of adjustable value, it is generally the maximum flow rate of Qmax 2%~4%, and the leakage is fully closed when the leak valve, it is only the maximum flow rate of 0.1%~0.01%.Adjustable range 100:1 generally can not reach, the accuracy of this valve is very high.

Q:Excuse me American Standard pressure test valve GB standards are much ~ is how much valve pressure can play much pressure? Thank you

Strength test is nominal pressure of 1.5 times, the test time is 5min, the test time, the valve body is not broken, no deformation, the valve is not leaking water, the pressure gauge does not drop to qualified. After the strength test has passed, the tightness test is carried out. The tightness test pressure is equal to the nominal pressure. The valve does not leak in the test time, and the pressure gauge does not drop to be qualified.

Q:Pump, valve, these belong to the material?

The pump belongs to the equipment (electromechanical equipment), and the valve belongs to the pipeline material.

Q:The total valve of my natural gas was closed by the attitude I tried. Now I can't open it. I need to use gas. Who knows how to drive it? What skills do I have? I'm talking about the main valve.

First of all, you have to determine the direction of the valve opening, usually homeopathy, it is off, the reverse is open. First: to determine the opening of the valve, are generally ball valve, screw 90 degrees on it. Second. At the top of your house, there is a button that can be pulled out. It's different from place to place. Some are pulled out half, and some are pulled out. Third: in the following there is a black disk like thing, commonly known as the gas sound core. This is the same as the second, pull out half or all, so that you can use gas, ha ha!

Q:Measure the temperature with a thermocouple, and then how to make the valve open when the temperature reaches a certain value. When the temperature is lowered, will the valve be closed?Or tell my brother what is the knowledge, I can see it myself. Good. How much extra?!

You don't know if the precision requirement of high precision can be used for high requirements of valve control valve (4-20mA) control but need converter needs the temperature signal into your current signal control valve (4-20mA) valve door factory will not have this thing you can ask to do control system manufacturers (in tell you part of the valve switch and adjust the price of at least 1000 points (OH) to not give me angry) is something you can ask me the valve factory

Q:Proportional valve why than other small pipeline valves

3.9 automatic control valveGraphical representation of numbers, names, symbols3.9.1 a pneumatic valve film head cut off the gas valve to maintain the original opening3.9.2 pneumatic valve closed to prevent head cut off the gas valve does not close the film3.9.3 prevent full pneumatic valve head valve does not open cell membrane3.9.4 basic type of pneumatic control valve3.9.5 pneumatic open pneumatic control valve, film head inflating valve opens3.9.6 pneumatic closed pneumatic control valve with membrane head closed3.9.7 pneumatic butterfly valve basic type3.9.8 pneumatic open air butterfly valve, film head inflating valve opens3.9.9 pneumatic closed air butterfly valve with film head closed3.9.10 pneumatic three way regulating valve combined type3.9.11 pneumatic three way control valve split flow type3.9.12 pneumatic valve with hand wheel basic type. Other types of valves with graphics by "people"3.9.13 with handwheel and positioner pneumatic control valve basic type. Other types of valves with graphics by "people"3.9.14 pneumatic cut-off valve three through 1 - 2 head membrane inflatable membrane head 2 - 3.3.9.15 electric control valve refers to the electric actuator with magnetic amplifier actuator3.9.16 electric valves are driven by ordinary single-phase or three-phase electric heads (motors)3.9.17 electric gate valves are driven by ordinary single-phase or three-phase electric heads (motors)3.9.18 electric butterfly valves are driven by ordinary single-phase or three-phase electric heads (motors)3.9.19 two position two way solenoid valve3.9.20 two bit, three way solenoid valve has 1 - 2 electricity, no electricity 2 - 3 links3.9.21 two position, five way solenoid valve P - gas source A, B - vent S, R - Exhaust

Q:Is there any problem with connecting the geothermal valves with other geothermal pipes?

Yes, as long as it's all PPR's.Material is the same, the fuse will not cause shrinkage when you can use