Q:The difference between cut-off valve and gate valve

The working principle is different. The stop valve is an upward stem type, and the handwheel rotates and rises with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!Gate valve and stop valve are shut-off valve, is the most common two valves.From the exterior, the gate valve is shorter than the cut-off valve, especially the bar valve needs a higher height space. Valve sealing surface has a certain degree of self sealing capacity, its spool depends on the media pressure tight contact with the valve seat sealing surface, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.

Q:What is the difference between gate valves Z41W-16R and Z41W-16P?

According to JB/T308P stands for Cr-Ni stainless steelR stands for Cr-Ni-Mo stainless steelCr-Ni stainless acid resistant steel has CF8, CF3, F304, F304L, which applies to the medium of work, such as nitric acid oxidation acid.Cr-Ni-Mo stainless acid resistant steel has CF8M, CF3M, F316 and F316L, which is suitable for working medium, such as acetic acid and reducing acid.

Q:What are the standards for the execution of cast iron dark pole gate valves?

They are also standard in the production of cast iron dark rod gate valves:Design and manufacture: as per GB/T12234-89 regulationsLength of structure: as specified by GB/T12221-89Flange dimensions: as specified in JB79 GB/T9112-9131Inspection and test: as specified in JB/T9092-99 GB/T13927-92Drive mode: manual, electric, gear drive

Q:Which is the most expensive, check valve and gate valve?

In the case of DN50 Z15T-16 DN50: screw valve 46.200 thread copper bar gate valve Z15T-16 DN50 52 Z45F-16 DN50 97 flange valve flange valve rod Z44T-10 DN50 169 Z45T-116 DN50 flange valve dark bar 173 thread swing check valves DN50 52.090 thread straight type check valve DN50 57.280 flange screw check H44T DN50 129 flange valve lift check valve H41T-16 DN50 124

Q:What is the standard length of GB steel gate valve?

1, product standardsGeneral purpose valves, flanged connections, iron gate valves, GB/T 12232-2005General requirements for steel valves GB/T 12224-2005"Steel flat gate valves for pipelines" JB/T 5298-91Inspection and test of valves. JB/T 9092-1999Standard for safety evaluation of drinking water distribution equipment and protective materials GB/T 17219-1998

Q:What is gate well?

Technical requirement:1: the valve itself can not seep, it must ensure its tightness;2: water supply pipeline during use, pipeline will be pressure from different aspects, which will produce different degrees of jitter or settlement, which requires the connection of water supply pipes and valves in the well to be reliable, able to adapt to a certain degree of jitter and settlement, and to prevent water infiltration into the well chamber in the pipeline valve wells; deep, slightly larger are generally made of cast iron valve (such as the cut-off valve, butterfly valve) iron valves long-term immersion in water, will affect the service life or cause fracture, so the sealing requirements are higher;3: valve shaft, shaft and well body, manhole cover way of connection should be reliable, not because of heavy rain or water seepage water into the well room.4: valve well is buried in the ground, to bear from different directions of different pressure, and different chemical substances corrosion and damage, and requirements of its pressure capacity and acid and alkali corrosion is better.

Q:What do you mean by gate valve type RVHX-0150-10 and Z45X-16Q?

Z45x-16q, Z means gate valve, 4 means flange connection, 5 refers to dark rod gate valve, X means rubber seal, 16 refers to nominal pressure 1.6MpaRVHX means manual gate valve, 150 refers to the caliber of DN150, and 10 indicates nominal pressure of 1.0MPa

Q:What kind of copper gate valve copper content standards, there are no national standards?

Copper gate valves are made of brass and bronze, and the national standard does not require copper content.

Q:What does gate valve Z41H-40 mean?

40 kg flanged cast steel gate valve；Flanged gate valve, 40 pressure

Q:The main question is, what are the functional differences in which case?

The gate (gate valve) is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle gate valve. The direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle.Gate valve advantages: 1, fluid resistance is small,.2, opening and closing more labor-saving,.3, medium flow unrestricted, not disturbed flow, do not reduce pressure,.4, simple shape, structural length is short, manufacturing process is good, a wide range of applicationsValve shortcomings: 1, between the sealing surface is easy to cause erosion and abrasions, maintenance is more difficult,.2, big size, open need some space, opening and closing time is long,.3, the structure is more complex