Butterfly Valve Without Pin Ductile Iron DN330

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
50 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.


Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
ActuatorBare shaft/Lever/Gearbox and handwheel
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Installation and operation instructions of knife gate valve
1. knife gate valve installation, check the valve cavity and sealing surface and other parts, not allowed to dirt or sand adhesion;2. bolts of connecting parts must be tightened evenly;
Q:What does Z941H-25DN250 mean by electric gate valve (excluding electric equipment)?
9- electric (drive)4- flange connection (connection)1- plain wedge single gate valve (valve structure)H-Cr stainless steel (sealing surface material)25- nominal pressure is 25 kg, or 2.5MPa;DN250- valve by 250mm
Q:The difference and use of gate valve and stop valve
Generally large and nominal caliber DN50 mostly with gate valve, especially industrial high temperature, high pressure, highly toxic and so on.Stop valve is able to stop and adjust flow, small footprint, small size, generally less than the nominal diameter, DN50 occasions use it. Two can be closed, in the flow of linear requirements are not high, you can adjust the flow. Just because of its structural characteristics of the valve to make its flow resistance, so there is a demand for throttling with a little more than the gate valve. In addition, the cut-off valve, whether it is a formal or reverse installed, in the opening and closing process, there is always a very difficult, and therefore can not do a great deal, or it is not easy to open and close. In addition, the cut-off valve has a one-way sealing effect of good features, so in the prevention of reverse flow of the working fluid, it also has a place to play.Hope to be of some help to you!
Q:What's the difference between open rod gate and dark rod gate valve?
There are several differences between the open bar gate valve and the dark rod gate valve:1, the bright bar gate valve can see the screw rod, but the dark rod can not see the lead screw;2, clear shot valve is threaded through the drive rod and the steering wheel to raise or lower the valve; dark rod valve in the switch when the steering wheel is connected with the valve stem is relatively fixed, it is through the stem of a fixed point in the rotation to drive the valve to move up and down to complete the opening and closing of the;Drive screw
Q:What are the advantages and disadvantages of flat gate valves?
The advantage of flat gate valve is that the flow resistance is small, and the flow resistance is similar to the flow resistance of short valve. The flat gate valve with guide hole is installed on the pipeline and can be directly cleaned with the cleaner. As the gate is sliding on the two seat surface, the flat gate valve can be applied to the medium with suspended particles, and the sealing surface of the flat gate valve is actually positioned automatically. The seat seal surface is not subject to thermal deformation of the valve body. Moreover, even if the valve is closed in cold condition, the thermal elongation of the stem will not cause the seal to be subjected to overload. The length of the structure is much shorter than that of the ball valve, and it is easier to start. Light plate gate valve is more refined, but the effect is exactly the same.The disadvantage of flat gate valve is that when the medium pressure is low, the sealing force of the metal sealing surface is insufficient, so as to achieve satisfactory sealing. On the contrary, when the medium pressure is high, if the sealing surface is not lubricated by the system media or foreign media, often opening and closing may cause the sealing surface to wear too much. Another disadvantage is that the circular motion of the circular gate in the circular flow, only when it is at the valve closed position of 50%, this valve is more sensitive to flow control. Moreover, the gate will produce severe vibration when it breaks the high-speed and dense medium flow. The valve seat can also be throttled if the seat is made of a V - shaped opening and is tightly oriented to the gate.
Q:What are the standards for the execution of cast iron dark pole gate valves?
Three, cast iron gate valve structure features:1.. The structure is simple and compact, the design is reasonable and novel, the rigidity of the valve is very good, the passage has a large flow area, the medium is unimpeded, and the resistance is small;2., the sealing surface of the material selected carbide and stainless steel, has a reliable sealing performance, long service life;3. cast iron dark rod gate valve using graphite material for packing, easy to operate;4., can use a variety of driving methods, such as manual, electric, pneumatic, gear drive, etc.;5., the position of the two sides of the gate valve is symmetrical, so the medium can flow freely on both sides, and the installation is very convenient;6. cast iron hidden rod gate valve structure length is short, the quoted manufacturing process is good, the scope of application is very wide;
Q:Notes on flat gate valves
Use, maintenance, maintenance and precautions1. valve before leaving the factory have made strength and sealing test, the use of all connections should maintain the initial state.2. this series of valve operating handwheel is marked with open and close rotary direction, and the upper part of rod is equipped with open and close height gauge for regulating indication.3. when the valve and pipeline welding, the valve should be opened, appropriate to protect the neck with moisture, minimize heat conduction, to prevent damage to the sealing packing parts.4. when the valve is closed, the lever shall not be used. When the gate is closed to the top, the handwheel shall be turned 1/2 so that the gate is in a floating state.5. in the use of the valve should be regularly to the valve cap injection grease joint into the quantitative grease.6., the valve in use, such as vulnerable parts and leakage, should be replaced in time.7., the valve in the overhaul process, the cavity should be cleaned, the assembly should be added to the transmission parts of grease.8. valve storage during the shutdown, the gate should be in the closed position, long-term storage should be placed in ventilated dry place, regular inspection and maintenance.
Q:What's the difference between a soft seal gate valve and a hard sealed gate valve?
Soft sealing gate valve is rubber seal, F sealed, hard sealing gate valve is the medium of particles.
Q:Z45T-10 what kind of material is the gate valve?
JB/T 308 regulation3.7.4 nominal pressure of less than 1.6Mpa gray cast iron valve body material code, in the type of preparation to be omitted.So its body material is gray cast iron, the sealing surface is copper alloy
Q:Function of gate valve
Gate valve is a closed (gate) along the central line of the vertical direction of the valve moving. Valve in the pipeline can only be fully open and fully closed off, can not be adjusted and the throttle. Gate valve is a valve used in a wide range, generally more than 50mm caliber DN block device is selected it, sometimes cut off very small aperture devices are used to gate valve, gate valve is used as cut-off media, when in full flow through the whole, when the media is running a minimal pressure loss. Gate valves are normally used in situations where they do not need to be frequently opened and closed, and the gate is fully open or fully closed. Not used as an adjustment or throttling. For high speed moving medium, the gate can cause the vibration of the gate under the condition of partial opening, and the vibration may damage the sealing surface of the gate and the valve seat, while throttling will cause the gate to suffer the erosion of medium.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range