Best B2 65Mn Forged Grinding Ball for Ball Mill/Cement/Mines/Powerplant
- Ref Price:
-
- Loading Port:
- Shanghai Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 200000M.T./Year m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Our grinding ball are widely used for powder preparation and extra-fine deep processing in sectors, such as cement building materials, metal mining, coal paste thermal power plants, chemical engineering, ceramic coating, light industrial paper making and magnetic materials. The cast grinding ball's hardness is high; wearing cost is low; the toughness is very good. So the breakage is few. The surface hardness of ball will be raised further in using the course, and the wear resistance would gather hard to raise mill machine production capacity and raise cement's ratio surface area and reclaim ratio of the extractive mine.
Specification of Best B2 65Mn Forged Grinding Ball for Ball Mill/Cement/Mines/Powerplant
Ball Diameter(mm) | |||||||||||||||
ø12.7 | ø 15 | ø 17 | ø 20 | ø 25 | ø 30 | ø 40 | ø 50 | ø 60 | |||||||
ø 70 | ø 80 | ø 90 | ø 100 | ø 110 | ø 120 | ø 125 | ø 130 | ||||||||
Chemical Composition of Best B2 65Mn Forged Grinding Ball for Ball Mill/Cement/Mines/Powerplant
Name | Designation | Chemical Composition | ||||||
C | Si | Mn | Cr | Mo | P | S | ||
Popular Grade | Cr10 | 1.8-3.2 | 0.3-1.2 | 0.2-1.0 | 10-13 | trace | 0.10 | 0.10 |
Cu | Ni | Nb | Ti | B | Zr | V | ||
trace | trace | trace | trace | trace | trace | trace | ||
Special Grade | Cr26 | 2.0-3.0 | ≤1.0 | 0.2-1.0 | 22-28 | ≤1.0 | ≤0.10 | ≤0.08 |
Cr20 | 2.0-3.0 | ≤1.0 | 0.2-1.0 | 18-22 | ≤1.0 | ≤0.10 | ≤0.08 | |
Cr17 | 2.0-3.0 | ≤1.0 | 0.2-1.0 | 13-18 | ≤1.0 | ≤0.10 | ≤0.08 | |
Properties and Microstructure of Best B2 65Mn Forged Grinding Ball for Ball Mill/Cement/Mines/Powerplant
Item | Designation | Hardness(HRC) | AK(J/cm) | Microstructure | Timesof FallingBalls | |
Quenched state | Non-quenched state | |||||
Popular Grade | Cr10 | ≥58 | ≥50 | ≥2.3 | M+C | 12000 |
Special Grade | Cr26 | ≥58 | ≥45 | ≥4.0 | 12000 | |
Cr20 | ≥58 | ≥45 | ≥3.5 | 12000 | ||
Cr17 | ≥58 | ≥49 | ≥3.0 | 12000 | ||
M-Martensite C-Carbide | ||||||
Notes: Composition varies under specific working conditions | ||||||
- Q: What kind of casting process is used for cast iron parts? And what are the cast steel parts adopted?
- Corundum sand: the main mineral composition is corundum alpha -Al2O3, used for investment casting, ceramic mold casting shell materials. The olivine sand: the main mineral composition of olivine (MgFe) 2SiO4, used in cast iron, non-ferrous alloy castings and high manganese steel casting molding sand and the core sand. Silica resources in nature resources, but suitable for casting with high SiO2 content of natural silica sand is not too much. Since 1951, China has carried out a general survey of the casting sand resources in the territory, but mainly limited to the main traffic lines and major industrial cities. Survey results show that Chinese can be used for natural silica sand casting is very rich in resources, a wide range of distribution. Inner Mongolia Zhelimumeng, natural silica sand reserves amounted to hundreds of millions of tons, the particle shape close to the circular, the content of SiO2 is about 90%. Fujian, Jinjiang Dongshan sea sand, the content of SiO2 is 94 to 98%, with a low volume of mud, are good natural silica sand. Are Duchang, Yongxiu Jiangxi County Xingzi, a large number of Quaternary lacustrine deposition of silica sand, the content of SiO2 is about 90%, low iron content, alkaline oxide less, uniform size, is a good lake sand. Guangzhou, Hunan and other places have abundant easily broken weathered sandstone, processing artificial silica sand, the content of SiO2 in more than 96%, can be used for the production of steel castings. Jiangsu Nanjing red sand, sandy mud pure, moderate, strong permeability, good viscosity, high silica content, less water, fine particles, pulls out the casting is smooth, stable quality, can be made of cast iron and non-ferrous metal parts of the sand and core sand
- Q: What are the casting parts processing engineering?
- According to the classification of process methods, sand casting and special casting.
- Q: What is the reason for 304 stainless steel precision casting parts to be changed?
- 304 stainless steel is easier to change than ordinary steel. Because the 304 heat conductivity is lower than that of the low doped steel, the temperature is even more uneven, and 20% of the non ferrous elements also make the distribution of internal and external elements more uneven, hard and soft inside. Each of these two produces greater internal stresses, resulting in a variant.
- Q: How much is the amount of electrophoretic paint per square meter used in the casting?
- It was a very simple question, and it was complicated by what you said.
- Q: How do you mark it on the drawing? Do you need to discuss it with the manufacturer?Because the casting allowance is the standard, then, after all, is the theoretical value, the actual level depends on the manufacturer, so is it necessary to ask the manufacturer?
- Casting parts do not need to provide drawings of casting blank, the casting factory according to your drawings in the required surface will be sufficient allowance, and the rest of the size according to the mechanical design manual and the casting manual can be found.
- Q: As shown, how do I achieve the tightness test of this product, and achieve industrial production? Seek expert advice.
- Precise and tight sealing of the surface to which the test piece is to be tested, equipped with an airtight test instrument, and an electrical control system. You can complete automated testing equipment
- Q: Why do casting parts have air holes?
- First, from the source, tools, raw material drying, in the process of melting into the reaction gas, another influence is pouring process, such as high temperature solidification gas dissolved too much after not excluded. The method can adjust the pouring temperature properly, control the source of gas (drying and controlling the inoculant, especially the content of magnesium), and add cooling iron to change the solidification mode. It depends on what kind of casting you are. You can't make it clear at once. And molding sand relationship is mainly water content and permeability, brush coating resin content.
- Q: Which surface is coarser for cast iron or cast steel castings? Why?
- The surface of the steel is more rough, because the coating sand cast steel cast iron particles compared with graphite coating degree, the other one is to get a better air permeability and collapsibility of sand, the compaction degree is smaller than iron. Roughness mainly depends on the surface roughness on the surface of the sand.
- Q: Why should pig iron be used in casting?
- Popular name is called pig iron, in fact, is a kind of cast iron without treatment, after casting, in iron elements to add other elements to improve casting performanceIt mainly improves the fluidity, reduces the melting point and reduces the shrinkage.Usually pure iron and cast iron at the eutectic point (about 4.7% carbon content) can be used for castingThere are many kinds of cast iron, usually grey cast iron, ductile iron and vermicular graphite iron......
- Q: How to solve casting defect casting?
- Different defects, different solutions, some shortcomings, the current domestic level can not be resolved
1. Manufacturer Overview
| Location | Anshan City, Liaoning Province,China |
| Year Established | 2002 |
| Annual Output Value | US$1 Million - US$2.5 Million |
| Main Markets | Domestic Market； South America； Eastern Asia； South Asia； Mid East |
| Company Certifications | ISO9001;IS014001 Certificate |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Shanghai Port;Dalian Port;Tianjin Port;Yingkou Port |
| Export Percentage | |
| No.of Employees in Trade Department | 6 - 10 People |
| Language Spoken: | English; Chinese; Spanish |
| b) Factory Information | |
| Factory Size: | 24,400 square meters |
| No. of Production Lines | Above 10 |
| Contract Manufacturing | grinding ball,grinding media,casting ball,casting grinding ball |
| Product Price Range | Average |
Send your message to us
Best B2 65Mn Forged Grinding Ball for Ball Mill/Cement/Mines/Powerplant
- Ref Price:
-
- Loading Port:
- Shanghai Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 200000M.T./Year m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
