Automatic Door for New Decoration Use Design

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
2000 set
Supply Capability:
200000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Automatic Door Glass Sliding :

1) Material:steel
2)Surface:heat transfer or powder coating
3)quality warranty is for10years
4)Surface Finishing: Finished

Features:
1) Material: cold-rolled steel
2) Frame outer size (H x W):
a) 2,050 x 860mm
b) 1,970 x 860mm
c) 2,050 x 900mm
d) 1,970 x 900mm
e) 2,050 x 960mm
f) 1,970 x 960mm

Name

Automatic Door

Glass used

1. glass thickness

single :4mm,5mm,8mm,10mm etc

insulated :5mm+6A+5mm,6mm+9A+6mm etc

2. glass type :tempered, low-E, laminated etc

3. glass color: gray, green, blue etc

Open mode

swing,revolving, sliding, etc

Features

Energy-efficient, heat and sound-resistant ,safe and  aesthetic etc

Others

We make windows and doors as per the standard and regulations of most countries and customers







Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Automatic doors can only open the reasons can not be closed
If the motor can be opened, indicating that the motor is no problem. The problem may occur on the controller. Controller is issued by the circuit board to change the direction of DC positive and negative direction to change the motor steering, in order to make the door run switch action. Most of this situation is generally a problem with the circuit board, different manufacturers in this circuit board to write the program is not the same.Therefore, after the failure of the circuit board is determined, it is best to contact the supplier to solve the problem (own solution Success rate is very small).
Q:What is the price of the Bill automatic door?
Smooth automatic door of the basic working principle is: installed in front of the door sensor infrared emission tube emitting a beam of infrared light, in the detection area to form a radiation surface, the radiation surface for the detection area, the light will be reflected in the target into this In a region, the infrared receiver detects and sends an electrical signal that reflects the red light. The signal is amplified, plastic input microcomputer. The computer according to the set procedures to command the motor and drive mechanism to work, so that the door set by the program to open, accelerate, full speed, brake slowly, close. When the door is closed when the door will be back when the obstacles, until the barrier is closed. As can be seen from the previous narrative, and then add some control components, by the controller can achieve more smooth automatic doors performance.
Q:Where is the speed of the automatic door?
LZ attention can basically be able to debug the national standards which are on the request is not the so-called "high-end machine can be"
Q:District automatic door project
If it is a closed area, there are residential doors and unit doors at the same time need to transform, in the choice of engineering before the first to understand the price of a good electric door machine, so you can probably know the total price level District door of the electric door machine has pull arm type, roller type, buried type.
Q:2000 Grand Am Se: Unable to Use Automatic Door Locks?
.The clicking you hear is the relay snapping shut. That really narrows the problem down. At least with that you know the remote, the receiver, and the coil feed is working. You need to get to the relay and see if it is getting power on the hot side (not the coil). If so then see if it is making contact to send the power to the locks. Then you'll have to just trace it to the doors. I seriously doubt both of the solenoids (part that locks and unlocks the door) went bad at the same time.
Q:What does side doors automatic mean?
When selector placed to automatic, if doors are open, evacuation slides would deploy - If selector in manual, evacuation slides do not deploy if door is opened - Doors must be in manual to permit normal door opening at airports - Doors are placed in automatic when taxiing for takeoff, until arrival after landing - Generally that command is not given by a pilot, but the senior flight attendant - Upon arrival after landing, command will be cabin door selector in manual -
Q:My automatic garage door opens, but stops after about 4 inches.?
JimS is correct. With the door closed, disconnect the opener arm from the door (there should be a release cord). Try opening the door by hand. If unable to, or the door is difficult to open, then the door itself needs servicing. This may include a broken spring or a bad torsion bearing. I would highly recommend having a professional repair the door. If the door opens and closes without a problem, then the opener itself needs adjustment. You can try gradually increasing the open force setting until the door opens without a problem.
Q:Automatic door opened when the door was detected and re-calculate the closing time, how is achieved?
It should be to receive the signal after the re-timing, sensor detection signal or other open signal control time relay opening and closing, time relay control door to open the door to keep it.
Q:automatic garage door will not stay closed because slab is pushed up by ice. anything i can do?
Pull the cord go to manual pull the door down an put rugs etc around opening take care of that in the summer.
Q:I hurt my arm at a shopping center chain that locked automatic doors?
The store did no such violation. They have a right to close the doors at closing time and they always do this. In fact, in a mall, if you are not out on time, sometimes, you are forced to exit at the opposite end of the mall and then walk all the way around to your car. If you could not open the door yourself, you should have had the sense to go find help and ask for it. Your other option would be to pay closer attention to the time and be out before they close the automatic doors. You have no case. The store was not negligent and you would have to prove negligence in order to have a case. It is unfortunate that you hurt your arm but, you did it yourself by using poor judgment. The store had nothing to do with your decision to try and open a door with your injured arm, which you knew was already injured.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range