Q:What is the difference between acrylic and PVC? Which is relatively better?

1. From the color points, PVC board stability is poor, easy to decompose when processing, generally with the same color of the acrylic than the background will be yellow. 2. From the density of points, PVC board density 1.35-1.4G / CM3, acrylic 1.1G / CM3, if the thickness and size of the same plate, heavier on the PVC. 3. Listen to the sound, with the area of almost two boards, to the floor light wrestling or hand percussion, sound crisp is the acrylic. Dull is PVC. 4. is burning smell smell. Acrylic burning flame yellow, alcoholic and smoke-free. While the flame when the PVC board was green, with hydrochloric acid smell, take white smoke.

Q:What is the difference between pvc floor and marble floor?

Material is not the same PVC lead Marble has radiation

Q:What is the cold mounted board

Cold plate of the bubble problem, the bubble phenomenon: dough and plate core blistering. Cause Analysis 1, board core curing period is too short; 2, neutral glue problems or glue is wrong; 3, into a plate after the sun direct or ultraviolet light irradiation. Common foaming is due to the dough is too thin, after the sun blunt, the picture and the dermis rarely blister, from the theoretical analysis is very easy to blister.

Q:How can PVC board be bonded together

PVC adhesive PVC Adhesive Formulation: Dichloromethane 100 Perchlorethylene resin 320 ~ 350 Dichloroethane 100 Tetrahydrofuran 60 ~ 80 Use This adhesive is used for the bonding of soft polyvinyl chloride products.

Q:Ordinary PVC board can be posted wallpaper? Or paint is mainly to improve its appearance

Can be posted wallpaper, but posted bad words, a long time will be bubbling ~ ~ This is the point of technology and careful Di tick.

Q:Pvc board density

PVC sheet Density (g / qm) Thickness range (mm) Low density free foam board (LD-FF) 0,5 - 0,6 3 - 25 Co - extruded core foam sheet 0,6 - 0,65 3 - 20 Crust foam sheet (CELUKA) 0,5 - 0,6 10 (8) - 30 Dense board * 1,4 - 1,5 0,8 - 20 cant see thing* 1,4 0,8 - 10

Q:Pvc foam board what materials?

Product Usage Widely used in passenger cars, train car roof, box core layer, interior decoration board, building exterior panels, interior decoration board, office, residential, public places building compartment, commercial decoration rack, clean room board , Hot plate, special cold-keeping project, environmental protection board mold, sports equipment, breeding materials, and other materials, the use of anti-corrosion, , Beach water-proof facilities, water-resistant materials, art materials and a variety of lightweight partitions instead of glass ceiling.

Q:I am going to be sealing the wall when making the basement a family room. Between the sump pump shooting out and the water traveling through the pipe, it's noisy. Anything that will quiet this?

You will never get rid of all the sound, but you might dampen it a bit by insulating around the pipes. You can use fiberglass insulation (batts) and stuff it around the pipe before you close them up. If you insulate the entire ceiling it will also keep the family room noise from disturbing people upstairs from noisy people down stairs. (I almost said from teenagers, but that might not be politically correct LOL).

Q:In the MDF posted a layer of PVC, is the plastic plate? But the plastic board is surrounded by the edge of the ah, who knows the name of this plate ah?

MDF, also known as fibreboard, is made of wood fiber or other plant fiber as raw material, urea-formaldehyde resin or other suitable adhesive made of man-made sheet. According to their density, divided into high density board, MDF, low density board. Dust board due to the soft impact resistance, but also easy to reprocess, in foreign countries is a good material for the production of furniture, but because the country on the high density board standards than the international standard several times lower, so the density board in China, the use of quality Still need to be improved.

Q:Pvc stone floor with hot water bubbles after the UV layer can be torn from the floor, and then you can smell the irritating smell, the business that no formaldehyde, but I think this taste UV layer is certainly sticking up and not hot The

Hello: I am PVC floor production process personnel, the so-called composite PVC floor layer is compound, and sometimes because of the composite temperature is not enough and other reasons there is no organic interface between the two layers of good, there will be opened The General UV layer is applied to the floor surface, the treatment did not solvent evaporation, the polymer in the coating is UV light cross-linked curing. Should not have such substances as formaldehyde. As for the source of the smell, may be the use of PVC additives and processing aids out of the question.