8 X 8 Aluminum Foil Pans

Hot Products

Double Side Aluminium foil laminated to fiberglass cloth

aluminum foil with LDPE for bubble foil facing production

Aluminum Foil Coated Bubble Insulation FBBF1001

Aluminium foil laminated to giberglass cloth

aluminum foil with LDPE film heat sealing for bubble foil facing production

aluminum foil with LDPE for bubble foil insulation production

Double side Aluminium foil laminated to fiberglass cloth

aluminum foil woven clother heat insulation material

Reflective aluminum foil insulation for building

aluminum foil with LDPE heat seal for bubble foil facing production

FAQ

Our end unit 1940"s row house has an old leaking bitumen roof . The water entry point can not be found so a replacement seems the way to go. A roofer suggested a replacement using Firestone 180, 1/2 inch fiberboard insulation covered with fiberglass base sheet, bitumen for flashing and fibered aluminum coating on wall coping . It's all Greek to be but fiberboard insulation and flashing material ? Should I be concerned?

We use kingspan insulation, marine grade plyboard , 3/4 inch, and yes you can use bitumen as flashing. I hope i am not being condescending, but the flashing is the bit that goes from the roof and a little way up the wall and is then "pointed" into the bricks, thus forming a water-proof barrier.

I have a vented metal roof. WV winters

Check into heat tape tied to pipe, with insulation wrapped around that. turns on when freezing temperatures. insulation by itself, will not stop it from freezing if left for long periods without water moving through it. .

or in queensland

Depends on whether you are employed or working contract. Currently it could be 18-25 per hr for employee or upto 40 per hr for contract depending on allowances and if you are providing your own vehicle or company vehicle. Then are you doing bats or anticon, it is usually charged on a sqm rate. Call some roofing companies or insulation companies and ask them what their rates are.

No insulation was installed under roof of my 2 story home. Im not rich but looking for info on installing about 450 ft. up there.

If there is no existing insulation you need a vapor barrier 1st or you need "faced" fiberglass, the one with either plastic or brown paper on it. I put it as thick as you can afford.

I would like to find foam type tiles for my roof of decking, insulation?

www.okorder I checked the website I posted by searching 'foam roofing' on google. This link is what I found but there are others... Google it to find your best deal. I think I will spray this stuff under my pier and beam home just to insulate. Thanks for the tip! I can buy this product, apply it myself and cut the cost down to 1/3 or more.

I gutted the room and now would like to rebuild. One side of the room slants (it's the roof) and the other side of the room is a dormer (all low ceilings).I want to insulate the ceiling but have no ridge vents so no moving air as someone mentioned I should have. I want to install foam channels to keep the insulation away from the roof but not sure if this is a good idea without the ridge vents. I will have a vent to the outside installed on the very top of the roof however and the small attic space is open all the way through the other two upstairs rooms and I will add another roof vent on that end of the house. I will only be able to install 3 inch insulation but that's better than none at all. I live in the northeast and was told if the job isn't done right I can get ice jams in winter. Also I don't see any way to drill ridge vents. would it be ok to just install the styrofoam channels and insulate then sheet rock or am I asking for trouble? Thanks in advance for any help.

Suggestion: install the insulation with the foam channels but leave the center section (roof ridge area) open from end to end. At each end you can install a static vent or an active one. Depending on the amount of space you have you may be able to install a power vent.If you can send me a diagram with measurements I can give you a more definitive answer.

were can i buy material to insulate pans and instructions to install it? I have seen many roofs with this done ,but , the lowe,s and home depots don't have .

I think your problem is in the way you are asking the question. I for one do not know what you mean by a metal pan roof. I know all about steel roofs or corrugated roofs and a lot of other roofs but what is a metal pan?

I am thinking about getting cavity wall and roof insulation at the moment.But since summer is approaching, I fear that getting the insulation will mean that the house will be very hot at night. (During day time the house will accumulate heat from the sun, and the heat cannot escape).I also fear that the ventilation will be bad and the air in the house will not be as fresh.Any advice please?

please stop worrying.your house will be warmer,but not hot.it is also a good idea to open your windows for at least 20 mins a day to allow claen/fresh air to circulate.you are correct in doing the job now though.