Q:Specifically an engine valve retainer.

Valve Spring Retainer

Q:Why anti condensation of aluminum alloy anti condensation butterfly valve?

Anti condensation butterfly valve multi-level unique progressive contact seat design, the valve plate in close contact in the process of gradually seat, ensure good sealing performance while reducing unnecessary torque, and the butterfly plate of stainless steel and the inner parts, thereby prolonging the service life of the valve seat, has strong rust and corrosion function. Torque reduction enables the drive to be lightweight and miniaturized. Unique stem seal prevents fluid leakage.

Q:What's the difference between an electric two position control valve and an electric butterfly valve?

The electric butterfly valve belongs to a kind of electric valve and electric control valve. The main connection modes of electric butterfly valve are flange type and clip type. The main forms of electric butterfly valve are rubber seal and metal seal. The electric butterfly valve controls the switch of the butterfly valve through the power signal. The product can be used as the shut-off valve, control valve and check valve of the piping system.

Q:That industry uses most of the butterfly valve, and only use the butterfly valve, a large number of use of butterfly valve, seek expert advice!

Large diameter heating pipes with more than butterfly valves, greater than or equal to DN600 are used butterfly valve

Q:What does the butterfly valve model d344h, d345h, d346h, d347h mean?

According to the international standard of the letters and numbers apart to explain D344H D is a unit of butterfly valve, two unit 3 is driving mode: turbine, three unit 4 connection: flange connection, four unit 4 Structure: seal type linkage, five unit H sealing material: Cr13 stainless steelD345H compare yourself to the above. Unit 5 four is a sealed, single eccentric structureD346H four unit 6 is an unsealed center vertical plateD347H four unit 7 is unsealed double eccentricIn general, there is only one difference between them: the structural form is different!

Q:What is the difference between the installation and function of a butterfly valve and butterfly valve?

Therefore, the fully open position of the valve is determined by the position of the gate. Some gate valve, stem nut is located on the gate, the handwheel rotates to drive the stem to rotate, and make the gate lift, this kind of valve is called rotary bar gate valve, or call dark rod gate valve. The type of gate width, sealing surface configuration can be divided into wedge gate valve and parallel gate valve, wedge gate type valve can be divided into: single gate type, dual gate plate and the flexible gate type; parallel gate type valve can be divided into single and dual gate gate plate. According to the thread position of the valve stem, can be divided into two kinds of open rod gate valve and dark rod gate valve. Valve installation and maintenance should pay attention to the following: hand wheel, handle and transmission mechanism are not allowed for lifting, and is strictly prohibited. Double gate valve should be installed vertically, that is, the valve stem is in a vertical position, and the handwheel is at the top. The gate valve with bypass valve shall be opened before opening to balance the pressure difference between inlet and outlet and reduce the opening force. The gate valve with drive mechanism is installed according to the instruction of the product instruction. If the valve is constantly switched on, lubricate it at least once a month. The valve has the advantages of small fluid resistance, the sealing surface by the erosion of small and medium Chong brush. Opening and closing is more labor-saving. Medium flow direction is unrestricted, no disturbance, no pressure reduction. The utility model has the advantages of simple shape, short structural length, good manufacturing technique and wide application range. Valve faults between the sealing surface can lead to erosion and abrasion, maintenance more difficult. Larger size, open need a certain space, long opening and closing time. Complex structure.

Q:For whatever reason, Mazda has made it next to impossible to change the PCV valve on the 929. I'm going to have to pull off the plenum and the passenger's side valve cover to replace a $2.00 PCV valve. Before I get too involved, I need to know the torque specs for the valve cover. Also, any other tips on this process would be greatly appreciated. Can I reuse the old valve cover gasket if it's still in good shape? Should I use any kind of sealant in addition to the gasket when I put it all back together? Thanks in advance, by looking at this motor, I can tell I'll have my work cut out for me (for a friggin $2.00 PCV valve, it's usually SO simple!). Like I said, any and all help is greatly appreciated.

you do not torque valve covers down, buy a new gasket , I would get a good quality rubber one and some blue rtv sealer, clean any crap off the valve cover no glue no bits of gasket nothing, same thing on the head surface, glue the gasket on the valve cover, let it set, then carefully put it on, start with the bolts in the middle and work out finger tight all of them, then just snug the bolts down, dont crush the gasket, you can also use a light duty locktite to hold them in place, and often times old valve covers are warped, it is too your advantage to make sure its as flat as you can get it, or spend a few bucks a buy a new one. your choice, but snug the nuts down good with out crushing and bending the thin sheet metal of the valve cover.

Q:How warm is the PTFE butterfly valve?

PTFE butterfly valve, sealing surface of fluorine plastic, temperature -29 ~ 450 degrees

Q:My bike has now 6200 miles on the odometer. The manual says that a valve adjustment should be performed every 6000 miles. But the bike runs fine. Can I just have the valve checked or should I have them adjusted even though the bike is fine? What will happen if I just keep riding it?

if the valves are not chattering (WOrse then normal) and you havent lost power or gas milage, then no...dont get it adjusted and no ... your not hurting the bike.

Q:How can I get the fire signal butterfly valve?

At the input end of the input module, some resistors or terminals are added to the product