It is characteristic of efficient energy-saving, small noise, reliable performance.
1,Vertical structure, same diameter for inlet and outlet in same axis, it can be installed in pipeline like valve, featuring compact and nice appearance, small covering area, small investment on building, available to use outdoors if equipped with protection casing.
2,Adopting mechanical seal or mechanical combination as shaft seal, it is made from quality hard alloy, with long service life.
3,Convenient maintenance, available to draw out entire rotor without dismantling piping system, as long as dismantle nut in pump body support.
4,In accordance with flow capacity and delivery lift required, adopt series and parallel operation.
5,According to the requirement of pipeline arrangement, adopt vertical and horizontal installation.
- Q:What about the oil quality of automobile engine oil pump?
- Take the pressure gauge to measure the pressure
- Q:From where on the car can you see that the oil pump is not oiled?
- Hello, not on the oil, then 1 valve sound than normal, 2, open the oil cap to see, 3, the best way is conditional removal of oil sensors, get off to see
- Q:When the car runs neutral, does the oil pump work?
- If the manual models can be linked to neutral way but now the car is EFI even idling is not fuel-efficient if automatic car driving process is completely not linked to the gap automatic models of the space is just in the car and trailer when used only
- Q:What's the cause of the indicator light of the car oil pump?
- In turn the ignition key does not start, oil should be light, because the engine lubricating oil channel has not been established in the oil, after the engine starts out as normal, such as after the start of light for the presence of faults, mainly due to the following: A: the oil shortage (more common)Two: the oil pressure switch (oil induction plug) fault (more common); three: oil pressure switch to the instrument between the fault lines exist; four: instrument fault (the possibility is very small: five) lack of lubrication system of internal pressure of the engine (more common) 1: dirty, too engine lubrication system within glioma lead, oil passages, set of filter clogging, so that the system does not establish normal pressure, 2: crankshaft bearing, connecting rod bearing, cam shaft bearing wear too much, resulting in failure to maintain lubrication pressure lubrication system, the machine oil lamps lit, 3: the oil pump internal blockage or too much wear, failed to build enough system oil pressure.The fault lamp is bright, must be timely to repair, did not identify the reasons before the engine will continue to drive the cylinder, crankshaft seizure fault, it must overhaul, to repair does not say, this is absolutely a damage to the engine.
- Q:Polo 1.4 changed the oil pump without oil
- Replace the oil pump and clean the oil passages
- Q:What is the influence of insufficient oil supply in the oil pump?
- Increase the load on the engine and damage the engine
- Q:What's the use of the oil pump for motorcycles?
- Two stroke engine oil pump is regulated through cable, throttle in the middle line will be divided into two, one to one to the carburetor, the oil pump, the throttle fully closed, then adjust the speed nut oil pump on the cable, the cable to completely relax, this is the minimum amount of oil, but be careful not to too loose, when the twist of the throttle, engine oil pump should follow the action, there is a situation of oil pump through internal wear caused by excessive amount of oil used for many years, this situation can not be adjusted, only the replacement of oil pump.
- Q:How do I see the motorcycle's oil pump is broken? Two red
- According to jog, it must be an organic oil pump, and if the oil pump is not oiled or oiled, there will be a problem, or look for experts to see, I just changed a few days ago the oil pump
- Q:Volkswagen Polo pump for heating lamp and light machine
- Oil lamp light generally has the following reasons: 1, oil pressure is not normal; 2, oil pressure induction plug failure; 3, related lines, bad contact, fault, etc.. Suggest going to the service station to have a check.
- Q:What are the markings on the fuel pump and the oil pump? They can be recognized at once
- It looks different
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average