Wear-resisting passage Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
1 unit
Supply Capability:
1000 Sets Per Month unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

products parameters :
Flow:Q=6.3~400 m3/h
High-lift:H=5~125m
Diameter size:φ=32~φ200 mm
temperature range :-15 °C~120°C

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Will it clog up the oil pump by cleaning the engine oil which is strong enough to clog up the oil circuit?
Not recommended, if you want to deal with the best in time to repair the engine oil, the remaining half after adding detergent, appropriate to start the engine, but don't let the engine run continuously, repeated ignition immediately stop, the three stop 5 minutes during the three times, then stop for 1 hours, began to disassemble the bearing replacement of oil with high pressure gas to clean up, and then the parts are cleaned, the abnormal wear or exceed the wear limit of a replacement, beginning of assembly, assembly of lubricating parts with clean oil, oil filter assembly, oil filter oil filling. Start OK.The use of cleaning function of the engine oil will lead to dirt in the oil pipe to fall off, plug the oil on the part of the small hole, exacerbated by the need for lubrication parts of the abnormal wear and tear, serious machine scrapped. The loss outweighs the gain。I have seen the use of this detergent containing oil, after the use of the whole machine scrapped, the landlord carefully.
Q:When the car runs neutral, does the oil pump work?
As long as the engine oil pump will work; but it is best not to in the automatic car speed of more than 60 temporal sliding block, then there will be damage to the gearbox is the main gearbox lubrication is not good
Q:What parts of motorcycle oil pump are connected with them?
It is connected with the engine crankshaft by the helical gear, turbine spiral rod combination, small chain and so on, and works simultaneously with the engine crankshaft
Q:How can Honda know when the pump is broken?
Hello, if the oil pump is damaged, the oil pressure light will be on
Q:What about the oil quality of automobile engine oil pump?
Take the pressure gauge to measure the pressure
Q:What is the difference between an oil pump and a gear pump?
The oil pump and the gear pump all play the lubrication role, the engine oil pump is delivers the engine oil each to lubricate the part, but the gear pump is 2 or more gears, when works, gives him the fuel injection
Q:How to change the oil pump?
Hello, that's very troublesome, I suggest you don't do it yourself.
Q:What part does the electromagnetic valve connect to?
The oil pump solenoid valve is used to realize the oil pump two or multistage oil pump pressure.There are two kinds of built-in and external.Built in solenoid valve installed on the oil pump, and in the oil tank, the external can not be observed, can only see the lead out of the connector.The external solenoid valve is also mounted on the oil pump, but the position is outside the engine and can be seen.
Q:110 engine oil pump gear is always broken, what should I do?
Change! 125 of my family have been riding for 10 years, without having repaired an engine
Q:What's the function of the engine oil pump?
The function of the oil pump is to send the oil to the friction parts of the engine, so that the engine oil is circulating in the lubrication road to ensure the engine to be well lubricated. The oil pump is mostly gear pump. It consists of gear pump body and so on. When the engine works, the camshaft drives the drive gear of the pump body. The gear swing oil flows along the inner wall of the pump from the oil inlet to the oil outlet, forming a low pressure to generate suction, and the oil in the oil box is sucked into the oil inlet. And the oil at the mouth of the oil more and more, and therefore increased pressure, oil will be pressed to each of the friction parts, the realization of forced lubrication.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location Hunan,China
Year Established 2006
Annual Output Value US$5 Million - US$10 Million
Main Markets 59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Africa
2.00% Oceania
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port SHANGHAI,GUANGZHOU,DALIAN
Export Percentage 51% - 60%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: Above 100,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average