Long Shaft Submerged Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
1 set
Supply Capability:
1000 Sets Per Month set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

They are widely used in the industries of petroleum, chemical, papermaking, metallurgy, sewage treatment etc.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The chain pump 2.4 of the modern business did not mark how to install?
Hello, there is a marking in the oil pump. Just install it directly
Q:What's the use of the oil pump for motorcycles?
Two stroke engine oil pump is regulated through cable, throttle in the middle line will be divided into two, one to one to the carburetor, the oil pump, the throttle fully closed, then adjust the speed nut oil pump on the cable, the cable to completely relax, this is the minimum amount of oil, but be careful not to too loose, when the twist of the throttle, engine oil pump should follow the action, there is a situation of oil pump through internal wear caused by excessive amount of oil used for many years, this situation can not be adjusted, only the replacement of oil pump.
Q:Does the car pump have a strainer?
The oil pump has no filter core, only filter screen, the oil is preliminarily filtered, and the oil filter is used to filter the oil again
Q:What are the fuel pump inspection items for diesel generator sets?
The main inspection items are as follows:1, the outer rotor and pump casing pump clearance;2, the internal and external rotor meshing clearance;3, rotor and pump cover face clearance;4. Flatness of pump cover.[diesel generator unit oil pump inspection notice]1, check valve planes such as abrasion, sag, pitting phenomenon, application of grinding paste on the plate grinding, severe cases should be renewed.2. The surface of the one-way valve seat on the shell should be replaced when worn or not smooth.3, the top rod and the top sleeve wear seriously, so that the gap increases, the seal becomes worse, diesel leakage seriously, you need to replace with the shell, or choose the enlarged size of the top rod, but need to pass mutual research.4, the coarse strainer tubing joints within the core, and easy to be cottony sundries plug, effect of fuel supply, it should always pay attention to the clean fuel and remove the dirt on the filter core.5, the hand pump piston rubber ring damaged, should be replaced in good time. After the center of gravity of the oil pump is assembled, the moving parts of the piston, the ejector rod and the other parts of the oil pump are required to be in good motion during the whole journey, and no blocking and blocking are allowed. The hand pump should be light and flexible. Pay attention to the installation of the one-way valve spring. The check valve spring must be accurately embedded in the spring slot.
Q:What's the reason that I changed the new oil pump instead of the engine oil?
Hello, either the quality problem, or the oil pipe is blocked.
Q:Manual transmission, organic oil pump, automatic, stepless?
Manual, no, automatic, yes
Q:The role of automobile gasoline pump
The oil pump is the role of the engine oil to the friction parts, the oil circulation lubrication in the road, in order to ensure good lubrication. The engine oil pump is composed of gear pump, gear pump body and other components. When the engine works, the cam shaft drives the drive gear pump rotation gear oil whip. Along the inner wall of the pump from the oil inlet flow to the outlet, the formation of low pressure, resulting in suction oil inside the oil is sucked into the oil inlet and the oil outlet. The oil product more, thus the pressure increased, the oil will be pressure to the friction part, realize the forced lubrication.
Q:The van is out of order. What's wrong with it? Can it make a noise?
The direct burning tile lubrication system basically does not work. The oil won't come. All moving parts are dry milled
Q:Single cylinder diesel engine crank bearing lock replacement, cause oil pump wear, replacement
Is the pressure on the oil (or engine oil) falling rapidly? Does the oil soon get dirty? The crankshaft is deformed and the cylinder head is partly blocked. The load can not last very long
Q:How to repair the Iveco oil pump
The oil pump can not be repaired by itself, nor can the repair factory repair it
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location Hunan,China
Year Established 2006
Annual Output Value US$5 Million - US$10 Million
Main Markets 59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Africa
2.00% Oceania
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port SHANGHAI,GUANGZHOU,DALIAN
Export Percentage 51% - 60%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: Above 100,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average