The introduction of High Quality Portable Coaxial Spray:
The High Quality Portable coaxial spray gun is the best choice for GRC products spraying by hand; It has a distinguished setting: it combines glassfiber cutting, mixing with other stuff such as mortar into identical spray nozzle, make sure the proportion of each different material, achieving the strength standard what GRC products require;
Data Sheet of High Quality Portable Coaxial Spray Gun:
Air-operated motor pressure: 0.35-0.45Mpa
Mortar pressure: 0.25-0.35Mpa
Fiber pressure: 0.20-0.30Mpa
Max rotate speed of air-operated motor:2500r/min
Granule Diameter: < ¢2mm
Fiber length: 30 -60mm
- Q:GRC light partition board installation scheme for construction of hydropower pipelines
- According to the trend line to determine the position of best hole in the circular hole; second round hole can be used for machinery, or homemade tools through a special hole, the effect is good, the size of the rectangular hole is larger, the machinability, good GRC panel can be cut by the saw, no problem.The GRC wallboard is assembled and assembled by a rabbet groove and can not be transversely laid by the heavy hammer and can not be laid transversely. When construction, the pipeline must be laid from the floor when it is buried. After the line is positioned, dig with a cutting machine. Laying, that is, with concrete mortar, add a proper amount of 107 glue and so on, at the groove to paste glass fiber mesh, with flat, to prevent cracking.
- Q:How many useful years does the GRC art component have?
- Like the GRC component of the general quality of the normal use is 20 years -30 years, like GRC friends of building decoration component of good quality can be used in 50-80, or the old truth, a penny goods, buy cheap GRC components, service life will be discounted.
- Q:How to identify new wall panels
- (1) GRC the highest cost, the main material cement from Hebei Tangshan (polar bears, 69 group), because due to the special cement, and the transportation cost per ton of cement and other reasons, than the local general cement expensive 150-200 yuan.(2) the cost of the other two new types of wallboard is almost the same.
- Q:What is the working principle of the mortar pump?
- 7, the piston 8 reversing valve at the same time, S 10 also reversing, the movable end and conveying cylinder 6 is 6 cylinder in the mortar conveying push 8 piston, enter S tube valve 10 is pressed into the discharge port 14; at the same time in the piston 7, conveying cylinder 5 inhalation of mortar, sent in preparation for the next step pressure. Thus, the mortar is pressed from the hopper to the conveying pipe, and this process is called pumping".
- Q:What are the features and capabilities of GRC components?
- From the material composition, the thermal conductivity is less than the general organic polymer inorganic non-metallic materials; thermal conductivity is smaller than that of the metal material; thermal conductivity of gaseous substances less than liquid substance, liquid solid material is less than. Therefore, the organic polymer material or amorphous inorganic material should be used as far as conditions permit, which is beneficial to thermal insulation. From the point of view of the material structure, when the apparent density of the material decreases, the porosity increases, and the pore inside the material is a large number of enclosed micro holes, the thermal conductivity of the material is relatively small. For foam plastics, the best apparent density is 16~40kg/m3 to meet the requirements of thermal insulation materials. Due to the existence of pores in the material in a humid environment, will inevitably be water, water and thermal conductivity (0.5815W/m - K) than ofstandstill air (0.0233W/m - K) is much larger, therefore, when the humidity increases, the equilibrium moisture content of materials increased, the thermal conductivity of materials will decrease. Therefore, as a thermal insulation material, the moisture absorption rate of the material itself should be as low as possible. If it is unavoidable, the material should be treated with water repellent or coated with waterproof material.
- Q:What about the air leak in the flue?
- When you want to see what kind of flue air leakage, the division of the usual general exhaust flue or kitchen flue, if the kitchen smoke exhaust, air leakage will be repaired immediately. To make, it is not can replace the exhaust pipe.
- Q:GRC jet equipment prices?
- This thing is high and low, automatic and semi automatic, the selected category.
- Q:Kitchen, toilet, GRC exhaust channel and glass magnesium plate exhaust duct advantages and disadvantages, and cost performance comparison?
- GRC light material exhaust flue defects:1, the process of artificial prefabrication is prone to uneven wall thickness of the finished product, resulting in low strength of the flue pipe, brittle, and flexible, shock resistance is not up to standard.2, artificial prefabricated smoke exhaust Road, low fire resistance, fire prevention is not up to standard, extremely safe and fire hazard.
- Q:What is a GRC pile composite foundation?
- The composite foundation is that natural foundation soil in the foundation treatment in the process of enhancement, or replacement, or reinforcement materials in natural foundation, the reinforcement area is composed of a base (natural foundation soil or improved natural soil) and reinforced artificial base consisting of two part. In the case of load, the matrix and the reinforcement share the load. According to the composite foundation load transfer mechanism of the composite foundation is divided into vertical reinforcement composite foundation and composite foundation level to strengthen the two class, and the vertical reinforcement composite foundation is divided into discrete material pile composite foundation and flexible pile composite foundation and rigid pile composite foundation three.
- Q:GRC what's the use of imitation wood?
- Test report, the company qualification, wooden doors do not know, I am specializing in GRC production and installation
ARTS, is engaged in environmental art, GRC projects. Our business scope mainly includes: bridge, embankments,garden fence railings, GRC European component,GRC / EPS prefabricated building component and engineering and garden hard landscape etc.
Our company has the capacity of independent mold development and GRC professional equipment manufacture.
1. Manufacturer Overview
|Annual Output Value
||Above US$ 10 Million
||20.00% North America
15.00% South America
15.00% Eastern Europe
10.00% Southeast Asia
10.00% Northern Europe
10.00% South Asia
10.00% Western Europe
5.00% Mid East
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||41% - 50%
|No.of Employees in Trade Department
||Above 150,000 square meters
|No. of Production Lines
||Design Service Offered;
Buyer Label Offered
|Product Price Range