Aerial Cable with Rated Voltage 10kv or 35kv
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 m
- Supply Capability:
- 100000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
AERIAL CABLE WITH RATED VOLTAGE 10Kv OR 35Kv
| |||||||||||||||||||||||||||||||||||||||||||||
1、Type and Applications
2. Standards It is manufactured in accordance with GB 14049-93, “Aerial cable with rated voltage 10kV or 35kV”. 3. Features Rated voltage U(Um) is 10(12) kilovolts or 35(42)kilovolts. It applies to the system of the duration of single phase ear thing fault normally less than 1 minutes each time or the system of maximum duration less than 8 hours each time, but the total duration not more than 125 hour. Ambient temperature should be not lower than -20℃ when cable is installed. Maximum temperature is 250℃ when cable is shorted for less than 5 seconds for XLPE insulated cable. For cable with weighted wire construction, maximum rated temperature of conductor is 90℃ for XLPE insulated cable. Minimum bending radius is as follows when cable is installed: for single-core cable- 20(D+d), unit: millimeter for multi- core cable- 15(D+d), unit: millimeter Note: D denotes the overall diameter of cable, while d means the diameter of conductor, unit: millimeter 4、 SizeSize
Note: 1. K denotes weighted stranding wire. You can select the corresponding cross-section in the above table as practical engineering needs. In the above cable construction it does not comprise weighted robe when the gap of tower poleis so large that it is necessary to add a weighted robe. 2. (A) means steel weighted stranding wire, while(B) means alluminium alloyed weighted stranding wire. 5. Pctures
| |||||||||||||||||||||||||||||||||||||||||||||
- Q:Hello teacher? Will a well a submersible pump supply two water towers, how to install the power supply, switch pumping do not interfere with each other more
- In fact, this does not meet the norms, if the future problems with the wire, would like to change for no change, because to lay cement mortar, are fixed dead, and assume that after the water pipes are leaking, not safe. Hydropower engineering design time should avoid the water pipes and pipe cross the place, can bypass to bypass, generally have a way to bypass, what the line to the wall. It is not around the cross should also be used to connect the elbow, but will lead to mortar leveling when the overall elevation of the ground, because it highlights the elbow Well.
- Q:Where can I find a power cable for an HP Photosmart C3180 printer?
- why don't you e-mail HP see if they will send you a power cord or advise you where to get one in your area
- Q:I have an IVI Checkmate receipt printer, but do not have a power cable for it. Where can I get a power cable for this receipt printer?
- Hi.. I think for all your power cable and cable accessories requirement this site can be helpful
- Q:How to connect the sound and the computer together
- The use of steel pipe as a wall, to solve the waterproof problem.
- Q:The chassis can not put the built-in burner, can be placed outside the chassis, because the Lenovo machine in front of only CD-ROM, there is no more rectangular space to put burners, but the external USB burner and too expensive, do not know the built-in burn Machine SATA data cable enough long, if the power line is not long enough how to do more
- Outside of the Ming Ming is on the host outside the burner friends. You want to put inside the chassis should have built the built-in
- Q:Want to buy a submersible pump to the home with water, about 90 meters away from home, what kind of pumps and cables should be bought?
- It is best not to cut the line directly to the extension line into
- Q:I am trying to wire up a tree light. All that comes out of the light is a Black White, and Ground wire. The instructions say you are supposedddd to install a Conduit and conduit connector which i dont have or really know what is. Can i install it without one. (AKA could i just splice it to a cut extension chord that also has a white black and ground?
- conduit is a metal pipe made for electrical use a connector is a pc made to attach 2 conduits together, yes just splice a ext cord to it,
- Q:Hi,1) Is spinning down of hard disk same as removing the power cable of the hard disk ? 2) Will the IDE cable connected carry power to the hard disk when the power cable is removed ?3) How do we spin down the hard disk manually ?
- 1) When you unplug the power cable, it spins down, because there is no power. In order to read data from the hard disk it needs to be spinning. When it is not spinning, you cannot read data from it. Some power saving systems will allow you set the hard drives to spin down after a long time that it has not been used, to conserve power. After that, to read from the disk it needs to be spun up, and that takes a few seconds. 2)No. 3) You cannot manually spin a hard disk, it spins at 7200 (some models 5400) rpm. That's VERY fast.
- Q:i have a mercury mystique gs wiring harness and i need to replace it so i was thinking why not copy the same layout as the old one i found one at junk yard thats fairly good shape i mean it doesnt work but i can copy it to make a new one so im wondering if anybody can direct me to how i can make one that looks and works exactly the same as a brand new wiring harness see if i had the option to buy a new one i would but they dont sell them anymore so im kinda stuck at this difficult decision
- The hard part will be finding all the special connectors. Then it boils down to making sure that you match the pins at both ends. You will have to use your own color coding or also do a lot of research to find the right colored wires. A soldering pencil that works on resistance is a handy tool, but a gun with a sharp point will do or a pencil iron. It is more work then I would want to do, but considering the cost of a replacement that is custom made it will be much cheaper. Some items are not in the system by the way and are what are called depot parts, which means that they are maybe a month away. A lot of parts persons don't know how to find obsolete parts, so maybe try a different dealer who as a real parts-man who can find what you want.
- Q:I purchased a LCD TV the other day and ran a cable line to it (via crawl space). I had to use a splitter to connect the new TV. I connected the cable directly to the TV and then the power cable to the outlet which “popped” and the power went out (breaker trips). I connect the TV power cable to a surge protector and the power goes out again (surge protector wasn’t even on). So I disconnect the cable from the tv and connect the power. Everything is fine until I try and connect the cable...let’s just say the spark was bright and hot enough to melt part of the connector on the TV! So I return the TV and get a different brand and the same thing happens when I plug it into a surge protector. To begin narrowing out possible problems I connect the cable to a regular 10 year old TV with no problems. It is a brand new cable with no cuts or fraying. Any suggestions?
- Something is seriously wrong, and you may need to get an electrician on the problem. You need to check the voltage between your set and the cable with a meter. There should be little or no measurable voltage. If you are getting a reading like 115 volts, then I suspect that the wall outlet into which your TV is plugged has been wired backwards, i.e. the black wire is on the white terminal, and vice-versa. The cable is (or should be) grounded where it comes into the house, but if the outlet has the hot wire on the wrong side, this might cause the problem you described. The wrong connection could have occurred anywhere along the line between your main panel and the outlet, so this may involve checking the connections at several outlets and light fixtures - whatever is on the same circuit as your TV's outlet.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Aerial Cable with Rated Voltage 10kv or 35kv
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 m
- Supply Capability:
- 100000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
