Square Paint Can Seaming Machine
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 1000 Sets per Month set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
tin can sealing machine
we are manufacturer of various of tin can making machine/production line,such as chemical can,food can,oil can,motor oil can,etc
Main technical parameter:
tin can sealing machine
Applying range |
50-330mm |
Production capacity |
Square-shaped can:12-15/min
Round-shaped can:15-20/min |
Electromotor |
Type: Y100L-6-V1
Power: 2.2KW
Rotating speed: 940/min |
Size |
1500×800×1800 |
Weight |
About 700kgs |
Main application:
1) This can sealer/sealing machine is one of necessary equipments in round or square tinplate can making production line. It is used to seal/close can lid/cover at can bottom/end at can body tightly, and without leakage. if customers want to seal other size of cans, just need to change the sealing/seamer mould.
2) This machine is used to seal various of tin cans,such as oil cans,chemical drum/barrels, adhesive barrels,etc.
- Q:Mm 0.2 enameled wire and copper welding, with spot welder good. Better with laser welder. Now the parts are machined with micro spot welding machine. Pressure and current are not good control, welding quality is not good, not welding is not strong, it will break.
- Resistance welding is suitable for processing materials with high resistivity. For copper, the resistivity is small, the heat consumption on the welder is large, and the efficiency is low. Small diameter solder joints can be brazed
- Q:How to change the spot welding point can have the longest service life
- With the electrode materials, the cost will be very high, the key in the adjustment and maintenance, setting current, welding time value is too high will definitely affect the loss; grinding is not standardized; the water is not in place; the electrode head according to the use of appropriate to increase the thickness of the welding ends;
- Q:The spot welder often stops itself and points out that the spot welding is not finished and needs to be done manually. Why is that?
- This is a lot of problem, you can check, PLC check the completion of welding signal steps have not received the completion of the signal.Normally, when a welder finishes a welding process, it outputs a signal to the PLC, and then PLC decides how to go next. This situation is vastly different, it is best to find the time to do this automatic spot welder manufacturers. Otherwise, you'll have to change all the control systems.If you change, you can find me, a lot of success stories.
- Q:The electronic spot welding point what material is good
- Made of copper welding point
- Q:When the spot welder is in use, the voltage of the line will be higher and lower. What can be done to solve it?
- The single-phase AC spot welder should be used. The single-phase power supply of AC spot welder has destroyed the balance of power grid and seriously affected the normal operation of other power equipment. The inverter type spot welder is supplied by three-phase power supply, and its operation does not affect the three-phase balance of the power grid.The power factor of welding machine is an important index that affects the utilization ratio of power supply equipment. If the power factor of welding machine is doubled, the requirement of power supply capacity will be reduced by 1/2. Because the resistance welding machine outputs is the low voltage, the big current. Therefore, the inductance of the secondary circuit of the welding machine is obvious, so that the power factor of the AC resistance welder can only reach 0.3~0.5. The inverter type resistance welding machine outputs DC welding current, and the power factor of welding machine can be as high as 0.95. Therefore, the requirement of the power supply capacity of inverter type resistance welding machine is less than that of the AC welding machine of the same capacity as 1/2.
- Q:What are the advantages of an intermediate frequency spot welder?
- The intermediate frequency spot welder (1000Hz) has the following obvious advantages:1. Welding specificationIf the response speed of the intermediate frequency spot welder is 1ms, the current can reach the set point more quickly, and can analyze parameters more and more accurately. The three-phase balanced input and the parameters are stable, and the constant current effect is stable;2. Welding qualityBecause of the frequency up to 1000Hz, the secondary frequency spot welder has good output ability of secondary current, and the waveform is flat and the size of the core is stable. Almost no spatter is produced, and the current in the primary stage of welding increases naturally, and the surface quality of solder joint is good.3, adaptabilitySuitable for welding many kinds of materials, such as aluminum alloy and aluminium, etc., which have fast heat conduction and poor weldability. The welding quality of galvanized sheet and ordinary multi plate is much higher than that of power frequency welding machine;4, transformerThe transformer is small in size and low in input power;5, energy utilization rateThree phase load balancing, power factor of more than 0.9, energy saving (according to the General Motors Corporation report, medium frequency spot welding, spot welding than power frequency welding, save 4 cents per point);6, auxiliary material utilization rate is no peak current and spatter significantly, shorten the time of welding electrode, long service life; improve the efficiency of AC, especially in the application of high speed welding.
- Q:Use 12 volt batteries.. Direct welding needle is used as spot welder.. Electric spot welding mobile phone battery.. Is it feasible?.
- If the electrode is in place, it may be ok
- Q:I have an annular core with a stack thickness of 40mm, a high 50mm, an inner diameter of 88mm, and an outer diameter of 168mm. I want to go around a spot welder or an electric welder. How many turns and how many turns are there in the first coil? How to calculate?
- Whether it is an electric welder or a spot welder, its power is relatively large, at least 3 to 5KW power!The power is mainly related to the sectional area of the core of the transformer and the number of turns of the winding!But your core cross section is only 40*50 = 200mm2, so it is too small to be a common welder! Only do other power transformers, such as power amplifier transformer!
- Q:Convex welding machine and spot welder difference, according to what kind of welding conditions choose convex welding machine or spot welder
- Projection welding machine is mainly in the board ahead of red bumps to welding, spot welding machine is directly to the two raw materials together in welding, this is relatively simple, so why take the convex point to welding, because there are the following questions, the material is very thick, not easy to weld, so a good welding convex point, the current requirement is not high; two, the high efficiency of the convex surface of welding spot welding, good effect, can be at a time of dozens of bumps, one-time welding, so more quickly. All belong to the resistance welding, each has its advantages and disadvantages, specific problems should be treated in order to achieve the purpose of super think.
- Q:Can 220V drive it?
- Spot welding machine belongs to resistance welding, low voltage high current, CO2 welding machine is arc welding machine, classification is different, spot welding machine is suitable for metal plate lap welding, but also can bump welding, CO2 welding machine is suitable for deep penetration of plate welding
In area of technic, research and development, We have a batch of professional and technical personnel in product development and manufacture and production management, some of our products have applied patent, so we believe our high technology and high quality products can meet the updating requirements of customers. We always keep "good business by sincerity and honesty, client's profit in first position" as our management principle. And we have been appraised as a corporation that "pay importance on contract, and keep sincerity" by local government for many times.
1. Manufacturer Overview |
|
|---|---|
| Location | Jiangxi,China (Mainland) |
| Year Established | 2010 |
| Annual Output Value | Below US$1 Million |
| Main Markets | South America 1.04 Southeast Asia 3.26 Africa 7.92 Mid East 8.81 Eastern Asia 0.54 South Asia 2.25 Domestic Market 76.18 |
| Company Certifications | Consumer Trustworthy Company;Member of Chiese packaging technology association;Trust-worthy Company |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | 41% - 50% |
| No.of Employees in Trade Department | |
| Language Spoken: | English, Chinese |
| b)Factory Information | |
| Factory Size: | 5,000-10,000 square meters |
| No. of Production Lines | 6 |
| Contract Manufacturing | OEM Service Offered Design Service Offered |
| Product Price Range | Average |
Send your message to us
Square Paint Can Seaming Machine
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 1000 Sets per Month set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
New products
Hot products
Hot Searches
Related keywords
