Gear planetary gear OEM hobbing,shaving,grinding for machine OEM
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 set
- Supply Capability:
- 10000 set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
| Material: | Steel,as requirements | Processing: | Forging | Pressure Angle: | 20 |
| Place of Origin: | Zhejiang China (Mainland) | technology of material: | forging | technology of machining: | hobbing,shaving,grinding |
| heatreatment: | nitriding,carburization | OEM: | is acceptable |
Packaging & Delivery
| Packaging Detail: | packed in carton |
| Delivery Detail: | 70days |
Specifications
1.produce as drawings
2.material will be as requirements
3.strictly quality control
4.OEM is acceptable
Products information:
1. suitable for many sorts of transmission system, such as agriculture tractor, wind power, truck and other industry zone.
2. material and precision can be as requirements.
3. we have complete gear machining equipments: gear hobbing machine, shaving machine, gear shaper, gear grinding machine, and our own heat treatment center. all of the production procedure are strictly controlled by ourselves, no cooperation procession, so we can sure the final products to meet your requirements.
4.each processing, strictly quality control
5.certificate: ISO9001, ISO/TS16949
- Q:A few days ago to a car POLO, accidentally remove the engine after the ring gear crankshaft behind the crank position sensor to get down, now the engine installed wouldn't burn, a question that is not the ring gear according to the previous position of the good, the master has repaired this a car I ha, very urgent!!!!!!!! Tell me in detail where it is there, the most important is the installation of the ring gear, the engine is 1.4 double cam shaft, 16 valve.
- Crankshaft position sensor: one of the most important sensors in the electronic control system of an engine. It provides ignition time (ignition advance angle) and signals confirming the position of the crankshaft, which is used to detect the upper dead center of the piston
- Q:Is the flywheel ring prone to failure?
- Reasons for operationWhen the engine is working, sometimes the driver mistakenly switches the ignition switch to the starting gear or causes a malfunction on the 4 moving circuit. If the ignition switch, relay and circuit in vehicle bumped when short circuit caused by a one-way clutch driving gear and the gear meshing force and strong ring scrape. Inspection found that when the situation occurs, most of the ring gear is worn evenly along the circumference, tooth tip 45 degrees chamfer, damage again start, two teeth bite difficult to make the phenomenon of milling more and more serious. This situation is not caused by starter fault, belongs to manual fault or circuit fault, resulting in milling. The method is to strengthen the training and study of drivers' operation, and to enhance their professional skills so that they can master certain theoretical knowledge and be alert to the use and operation of vehicle equipment. In particular, the restart operation of the starter must be strictly spaced at the time of starting. The correct method of use is that the total time of each vehicle is not more than 5 seconds, and the interval is not less than 15 seconds. Also note that the use of starter uninterrupted when starting car will cause the battery due to excessive discharge and damage to the vehicle battery charging condition in time to check whether the lack of electrolyte without added electrolyte must be timely according to the provisions. We do this through the transformation of installing a protection device to prevent repetition priming to protect the engine flywheel ring gear flywheel ring gear and extend the service life of the starter.
- Q:Can the parameters of the starter gear be deduced according to the parameters of the flywheel ring gear of the engine?
- The two parameters, the modulus m of the starter gear and the pressure angle alpha, can only be deduced,
- Q:Parameters of flywheel ring gear for single cylinder diesel engine
- So you have to be sure what your diesel engine is
- Q:Ring gear material 50Mn heat treatment, conditioning is shrink or rise?
- Is up. Because the 50Mn before heat treatment is ferrite = pearlite, and after heat treatment is martensite (including tempered martensite), the specific volume of martensite is larger than ferrite and pearlite (surface oxidation does not count).
- Q:How to install the gear ring of the rear oil seal of Lang Yi crankshaft?
- A brief introduction to the crankshaft:The main rotating parts of the engine, with the connecting rod, can take the connecting rod up and down (reciprocating) movement, into a cycle (rotation) movement. It is an important part of an engine. Its material is made of carbon structural steel or ductile iron. There are two important parts: the spindle neck, the connecting rod neck, and (the others). The spindle neck is mounted on the cylinder body, the connecting rod neck is connected with the big hole of the connecting rod, and the small end hole of the connecting rod is connected with the piston of the cylinder, and is a typical crank slider mechanism. The lubrication of the crankshaft mainly refers to the lubrication of the connecting rod, the big end bush and the crankshaft connecting rod neck, and the lubrication at both ends of the connecting rod. The rotation of the crankshaft is the power source of the engine. It is also the source of the whole mechanical system
- Q:There is no gear with teeth inside or outside, or it is called a ring. The inner teeth are used for internal meshing, and the outer teeth are used for external meshing. Thanks for your help
- Both inside and outside the teeth have more gear. Our company also produces these. This output, as you say, has been applied on many machine tools. It is recommended that you refer to the differential output on the gear hobbing machine.
- Q:What is the radial runout error of the ring gear?
- The radial runout error of gear ring is a standard for gear post test. Generally speaking, it represents the difference of the teeth on the circumference of a gear. Popular point of view, with the detection of the beating of the outer circle almost, but the benchmark is on the teeth.
- Q:Why a screw worm gear ring interference fit to cast iron core wheel side bias
- The drill can tilt to the side of the crown, in order to reduce or avoid this happening so the hole center bias cast iron wheel core side.
- Q:How many teeth of the 12 gear starter is suitable for the gear ring?
- Starter 12 teeth are 1332d, 1315c, 138C, 140, 141, 1115 and 195 and a single cylinder gear and ring gear with them, usually in a single cylinder diesel engine, according to the installation position selection.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Gear planetary gear OEM hobbing,shaving,grinding for machine OEM
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 set
- Supply Capability:
- 10000 set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
New products
Hot products
Hot Searches
Related keywords
