Led Fluorescent Tube T12

Led Fluorescent Tube T12 Related Searches

Led T12 Tube Light Bulbs Led Fluorescent Tube 3Ft Led Fluorescent Tube T12 Fluorescent Light Ceiling Fluorescent Light Tube Covers Fluorescent Light Desk Lamp Fluorescent Light 4 Foot Neon Fluorescent Light Tubes Linear Fluorescent Light Fluorescent Light Lumens

Hot Searches

Led Fluorescent Tube T12 Supplier & Manufacturer from China

Okorder.com is a professional Led Fluorescent Tube T12 supplier & manufacturer, offers integrated one-stop services including real-time quoting and online cargo tracking. We are funded by CNBM Group, a Fortune 500 enterprise and the largest Led Fluorescent Tube T12 firm in China.

Hot Products

FAQ

A set of lamps and lanterns
Very specific, T5. T6, T8, how many W's, how many roots, I'll do it for you.I hope my answer is useful to you
The difference between LED and fluorescent lamps
LED is a solid-state light source that has a long life and is environmentally friendly and efficient, and leds are now safer.
Why don't leds need a rectifier
Leds also require a power supply to drive only the rectifier that is not the tube. Normal LED daylight tubes are not driven. You have to have a power supply drive, and you have a built-in driver but that's going to affect the life span of the power supply and you don't have to be able to do that without the wiring.
How much is the ballast of the fluorescent tube coming out
IME's "flash" is pretty good. They've been working with them all the time, and the quality of the product is assured. 3W's LED skylights are only 14, 5 yuan, and in baidu's search for flash, fans can find their website. Other lamps and lanterns also sell very cheap, have the day flower lamp, shoot lamp, sunshine tube, ball bubble lamp, soft lamp belt and so on
The lighting is replaced by LED lights and circuit problems
No, you're going into a ballast, one is out. The picture you gave is only part of it. When you disconnect the ballast, connect the same color. The red one is the wire, the current of the ballast. After disconnecting, it should be a connection between the red wire and two broken wires. You should shoot the right wire again. The situation in my home was to tear down the ballast and the two red lines were connected to the red line. The green earth line connects to the blue line. You have to capture the essence of the problem, and you have to see the current flowing. The current must be in and out of the ballast. When you disconnect the ballast, you should connect the broken one to the other. This will make the current pass.
Is there a ballast in the LED lamp? Or do you need a ballast?
There is no driving module, and the LED is in a dangerous environment even if the voltage meets the working conditions. As a result, the driving source of the LED work is very important.
How do you know whether a fluorescent tube is good or bad
There is a small filament in each end of the normal daylight lamp, and the two feet on each side of the lamp are interlinked with the multimeter (only very small cold resistance). Working principle is: making after vacuum tubes when filling the silver (mercury), a small drop of water on the walls painted with fluorescent powder, the bulb is started, at the ends of the filament after heating, mercury evaporates into gas, gas is ionized conductive lines into loop, gas release a large number of ultraviolet (uv), at the same time by the ultraviolet radiation fluorescent powder from visible light. In addition, when after the lamp aging on both ends of the filament evaporation guide to black on both ends of the tube, the tube sometimes no broken cannot use the filament lamp to glow (so).
What is the flux of the general led daylight light
See how many wattage, generally 16 w LED fluorescent lamp at present is 1400 lm, luminous flux or new 40 w fluorescent lamp luminous flux highs, but according to the high degree is the LED fluorescent lamp, fluorescent lamp, 360 °, reflective part by stent, the light loss is very big, the LED fluorescent lamp light Angle generally around 170 °.