Fluorescent Light Globes

Hot Products

T5 Circular Energy Saving G10Q Fluorescent Lamp

Hid Bulb D1 12V 35 Watt

Road Lights Lighting Fixture with Energy Saving Induction Lamps

T8 tubes 9 w - 0.6 meters 0.9 meters 12-1.2 m 14 watts LED daylight tube

Sodium Luminaire Lamp 600 Watt

G45 Milk White Light

Mercury Lamps 250 Watt with High Pressure

Halogen Bulb

Energy Saving Lamp

H1 Hid Xenon Lamp 12V 35 Watt 6000K

FAQ

Is the energy-saving lamp a fluorescent lamp?

The energy-saving lamp belongs to the fluorescent lamp class.The same power of energy-saving lamps should be incandescent lamp brightness of more than 3.5--8 times.

Are there any differences between fluorescent lamps and energy-saving lamps? What are the differences between them?

Rare earth phosphors are mainly used in office, store and factory high performance fluorescent lamps. Since the middle of 80s, with the development of less expensive fluorescent phosphor containing terbium, the application of this energy-saving lamp has been increasing rapidly. In mid 90s, the international launch of the TMT2 straight tube fluorescent lamp, the diameter of only 7mm, power is 6W~13W, light efficiency is 621m/W.T5 straight tube type fluorescent tube diameter is 16mm, power 14W~35W, 28W fluorescent light up to 104m/W, life is more than 16000h. in new development of high power light type 55W~120W is suitable for outdoor lighting compact energy saving rare earth fluorescent lamp, light efficiency more than 801m/W.

Why can fluorescent lamps emit various colors?

Phosphor of red, green and blue three colors, yttrium oxide (red light, peak wavelength 611nm), magnesium aluminate (emitting green light),The peak wavelength is 541nm) and the barium magnesium aluminate (blue light, with a peak wavelength of 450nm) mixed in a certain proportion can be obtainedFluorescent powder of any color can be sent out

How to adjust light in fluorescent lamp

Fluorescent light dimming can also extend the life of the light source, dimming to 90%, doubling the life of the light source; dimming to 80%; the light source life is extended two times; dimming to 50%; the light source life is extended ten times. Although this is a theoretical value, but shows that fluorescent lamp dimming can also reduce the frequency of replacement of the light source, the light source in the unit of time to reduce the amount of change a lot, it also has its positive significance for energy saving and emission reduction.

Maintenance and repair of fluorescent lamp

If the voltage is low, the lamp will light up in the beginning of the two pollutants emitted tungsten, so that the lamp tube produces many point, one of the reasons to become tube damage so that, as far as possible in the high voltage under the condition of light.

What's the difference between an energy-saving fluorescent lamp and a LED light?

Different lighting principleAn energy-saving fluorescent lamp uses mercury vapor at low pressure to release ultraviolet light after energizing so as to make fluorescent powder coated on the inner wall of the lamp tube shine.The light emitting element of the LED is a semiconductor crystal,

What are the types of fluorescent lamps?

Relationship between the diameter of fluorescent lamp tube and its electrical parameters:1, fluorescent tube, the smaller the diameter, the higher the light efficiency, the better power-saving effect2. The smaller the diameter of the fluorescent tube, the higher the ignition voltage of the glow lamp, the higher the technical performance requirements of the ballastThe diameter is larger than T8 (T8) fluorescent lamp starter ignition voltage is low. Compared with 220V, 50Hz AC, with starting ignition voltage less than 1/2 power supply voltage law. Can use inductive ballast, for starting and lighting operation.

What is a fluorescent lamp? What are fluorescent lights?

The traditional fluorescent lamp type fluorescent lamp and electrodeless fluorescent lamp, traditional fluorescent lamp is a low pressure mercury lamp, mercury vapor is the use of low pressure in the discharge process of ultraviolet radiation, so that the phosphors emit visible light emitting principle, so it belongs to low pressure arc discharge light source. The traditional fluorescent lamp is equipped with two filaments. The filament is coated with electronic emission materials, three yuan carbonate (barium carbonate, strontium carbonate and calcium carbonate), commonly known as electronic powder. The alternating filament acts as a cathode and anode under alternating voltage. The inner wall of the lamp tube is coated with phosphor powder. The tubes are filled with argon at 400Pa-500Pa pressure and a small amount of mercury. After discharge, the liquid mercury evaporates into mercury vapor at a pressure of 0.8 Pa. In the electric field, the mercury atoms continuously from the original state is excited into the excited state, then spontaneous transitions to the ground state, and the radiation wavelength of 253.7nm and 185nm (the peak value of ultraviolet wavelength is 253.7nm, total radiation energy 70-80%; peak wavelength is 185nm, accounting for about 10% of the total radiant energy), to the release of excess energy. The fluorescent powder absorbs ultraviolet radiation and emits visible light. Fluorescent powder is different, the light is also different, that is, fluorescent lamps can be made white and various colors reasons.