316 Stainless Steel Wire Mesh
316 Stainless Steel Wire Mesh Related Searches
316 Stainless Steel Wire Mesh Supplier & Manufacturer from China
Okorder.com is a professional 316 Stainless Steel Wire Mesh supplier & manufacturer, offers integrated one-stop services including real-time quoting and online cargo tracking. We are funded by CNBM Group, a Fortune 500 enterprise and the largest 316 Stainless Steel Wire Mesh firm in China.
I want to get an underground fence but i cant figure out what the difference in the wire they use and regular insullated wire. What is the difference and why can't i use regular wire instead of the wire that comes with the kit
- There isn't anything special about the wire that comes with the kit, it is just wire. If you have already installed the fence and just need to enlarge the area you can use your own wire just make sure it is the same gauge wire as is already hooked up.s
I just learned how to do 3-way wiring, so that I can turn a light off from 2 different switches. My question is, how do I add another light to that mix, so that both lights come on/go off at the same time when I turn the switches on and off? (It's for a closet that has 2 lights in it that I want to come on/go off at the same time).
- You have to tie the wires that go to the light together. It is called parallel.s
What is a tubeless wire and how does it work?
- It is a wire without a tube. It works properly, it has a larger section than the usual wires, but is cheaper (Al is cheaper than Cu).s
i have 4 wires going to a ac unit #10 wires 2 wires for each cir. and i need to know how many amps can I run with 2 #10 copper for one side of the breaker
- 10 wire is rated for a maximum of 30 amps. This size wire can not be run in parallel to carry more current. I suggest that you have a local qualified professional electrician do the work since you seem unsure about what you are asking.s
Wire 1 and wire 2 are made from the same metal. Wire 2 has a larger diameter than wire 1. The electric field strengths E1 and E2 are equal. A) Compare the values of the two current densities. Is J1 greater than, less, or equal to J2?B) Compare the values of the currents I1 and I2. Is I1 greater then, less or equal to I2?
- The current will be more dense in the smaller wire. The value of the current is inversely proportional to the resistiance of the wire. Resistance = resistivity * length / Area since the wires are of identical material and length, the only thing left to vary is the cross-sectional area. Area is proportional to the square of the radius (diameter), so the current will be proportional to the square of the diameter. I2 is proportional to I1^2 I2 is larger than I1 .s
So earlier my passenger low beam wouldn't turn on. i went and bought a circuit tester and found out a wire located here _-_ lt;=== (the bottom right plug on the socket) that wire wont light up. i bought a socket at the same time, but i dont know how to replace it. and even if i did.. i don't see how that would fix the wire.It's possible the wire is fine. but i cleaned the socket and all that and still nothing.any advice would be great. i really need to drive at night1994 GMC jimmy
- Your rig is 17 years old. The wires at the plug shrink and crack from heat and age. Then they get water into them and corrode inside where you cannot get at it. Does not happen with all cars, but when it does, it is a royal pain. Either try for a new plug/harness or cut one out at the junk yard and splice it in. Use heat shrink over the splices.s
I am wiring a GFCI receptacle with two regular receptacles after it.So before the GFCI I have my 12/2 wire from where it will hook into the box (the line side), after it I have my wire going to the two other receptacles (the load side).Well the GFCI receptacle has screw terminals for the line HOT and WHITE wires as well as a GROUND. On the bottom it has screw terminals for the load side but ONLY the HOT and WHITE, no ground screw.Does this mean that I don't hook up the ground for the load wire or does it mean I have to pigtail the ground to the same screw the line ground is using?I didn't want to assume that I connect the line and load grounds out of fear I was circumventing the GFCI.
- The grounds all are attached to the same ground screw, twist all of the ground wires together and bring one wire to the screw. There are ground wire nuts, green with a hole in the end, put one of the ground wires through the hole and then twist all of the others under the nut.s
A street lamp weighs 200 N. It is supported by two wires that form an angle of 130° with each other. The tensions in the wires are equal.What is the tension in each wire supporting the street lamp?If the angle between the wires supporting the street lamp is reduced to 100°, what is the tension in each wire?
- Problem 1: If the tension in the two wires are equal, the angle they make with the horizontal must also be equal. Always remember that a horizontal line is a straight angle; hence, it has a measurement of 180°. Let's look for the angle the wires make with the horizontal. 130 + x + x = 180 130 + 2x = 180 2x = 180 - 130 2x = 50 (Divide both sides by 2) x = 25° Each wire makes a 25° angle with the horizontal. We can now find the tension. The mass must be divided by 2. Using trigonometry, let's find the tension force. The divided weight of the lamp shall be the opposite side, and the tension force shall be the hypotenuse. sin 25° = (200 / 2) / Ftens Ftens = 100 / sin 25° Ftens = 236.62 N (Answer) The tension is 236.62 N in each wire. Problem 2: We use the same approach. 100 + x + x = 180 100 + 2x = 180 2x = 180 - 100 2x = 80 (Divide both sides by 2) x = 40° Each wire makes a 40° angle with the horizontal. Calculate the tension force. sin 40° = (200 / 2) / Ftens Ftens = 100 / sin 40° Ftens = 155.57 N (Answer) The tension is 155.57 N in each wire. Hope this helps!s
How much are chains for tires
- Tyre protection chain, is a link and connection between the link on both sides of the body of the chain components, connecting link in the side chain and the connection on both end...
what is pcb used for
- What is pcb used for？For a long time, PCB buyers have always been puzzled about the color of PCB, they do not know what the color of the PCB board is the quality of. What kind of...
what is a fastener
- Generally the fasteners include the following parts： what is a fastener---Bolt: a type of fastener, consisting of two parts of the head and the screw (with an external screw cyli...
what is bolts and its application
- What is the mechanic knows that what is bolts. Bolt, with nuts cylindrical threaded fasteners. Is a machine part, usually fixed in the periphery of the mechanical equipment, bolt b...
Explain to you what is abrasive
- What is abrasive？This is a problem that everyone wants to know.But what is abrasive? what is abrasive?--- The general name of the hard material in the process of grinding, which ...