ZJ1300 x 2.0 Slitting line
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Ⅰ. Technological Capability:
1.1 Raw material: carbon steel strip, fine steel strip, and low alloy steel strip
(σs≤350MPa,b≤500MPa )
1.2 Specification of raw material:
Thickness of steel strip 0.25 - 2.0mm
Width of steel strip 700 - 1300mm
Inner diameter of strip coil 508mm
Max Outer diameter of strip coil 1800mm
Max weight of strip coil 10 tons
1.3 Finished Product
Inner diameter of strip coil 610mm
Outer diameter of strip coil Max1800mm
1.4 Slitting capacity
quantity of srip 8 - 15 strips
1.5 Max Line Speed 100m/min
1.6 Input Power: 380Volt, 3 phase, 4 lines, 50Hz.
1.7 Feeding Direction: Left side or right
II Technical flow:
Coil loader → Uncoiler → shovel board device → Feed Flattener → end shear → Centering device→ Slitter→ scrap winder → Accumulator →tension stand→ Recoiler→ Movable support→ Separating Presser → coil unloader
- Q:In the process of metal cutting, the process of chip formation consists of several deformation zones
- Second deformation zone (fibrosis); third deformation zone (fibrosis and work hardening).
- Q:What are the main factors that affect the quality of metal cutting?
- Mechanical surface quality refers to the micro roughness of the machined surface after the machining, also known as roughness. The surface quality of the machined parts directly influences the physical, chemical and mechanical properties of the machined parts. The performance, reliability and life of the product depend to a great extent on the surface quality of the main parts.
- Q:What are the differences between metal cutting equipment and metal processing equipment?
- Metal processing equipment is divided into many kinds, metal cutting equipment is one of the metal processing equipment, such as vertical lathe belongs to metal cutting equipment, but also metal processing equipment
- Q:All the parts on the machine must be machined by metal cutting, right?
- No, for example, turret weights, I've seen a direct cast hole.
- Q:How about the metal cutting parameters?
- According to the cutting force allowed by the process system, including the machine feed system, workpiece rigidity and surface roughness requirements during finishing, determine the feed rate.
- Q:Causes of retention of mechanical metal chip cutters
- Product cut tumor is unstable in the cutting process, it is time now, later, to a certain height, broken by the workpiece and cutting away and disappear, and then destroy the estate was born again and again. The surface of the workpiece is uneven and the surface roughness decreases. It also causes vibration during cutting and speeds up tool wear.
- Q:What's the name of the machine that processes cutting tools?
- Many cutting tool processing is to design and manufacture special fixture.
- Q:What is the rigidity of process system in metal cutting?
- When the lathe tool cuts the workpiece, the cutting forces on the cutting edge and the workpiece are affected by equal and opposite cutting forces, while the component Fy of the cutting force has the greatest influence on the machining accuracy. Under the influence of the cutting force, the tool (due to the deformation of the process system) and the relative decline of the workpiece.
- Q:What is the relationship between metal cutting and numerical control machine tools?
- Metal cutting is more extensive, it can be said that the basic machinery belongs to.
- Q:What are the unsafe modes of metal cutting machine tools?
- Glove handling,don't wear protective glasses,feed too fast, the metal parts are too small to use hand feed.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
ZJ1300 x 2.0 Slitting line
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords