Strut Channel
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 100 Meters m
- Supply Capability:
- 200000 Tons per Year m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Common Size:
Size (mm) | Thickness (mm) | Material: - Pre-Galvanized - Hot Dipped Galvanized - Back to Back available
- spring nut, bolt, nut & washer are available |
27x15 | 1.2-3.0 | |
41x21 | 1.2-2.5 | |
41x41 | 1.2-2.5 |
Hole sizes:
10*25 / 14*28 / 11*25 / 10.5*30 / 12*35mm
Our Comnany:
Octopus Metal is specialized in support channel, galvanized steel coil distribution and cable tray manufacture.
We operate 2 large-scale factories with advanced equipments. Our product have passed SGS and CE certification.
- Q: What is the difference between a trunking and a bridge in a weak construction?
- I would like to talk about the hope that useful
- Q: Single-core cable on the bridge why the buzzing
- Of course to vibrate. The conduction conductor is the same current absorption, the opposite current repulsion.
- Q: Is not the cable bridge, the whole plant laying a flat iron, each layer of equipment to the ground bus to the bridge on the flat iron, rather than on the bridge. Is this the requirement? More
- Grounding flat steel should not be laid in the bridge, the cable bridge should be connected into a reliable electrical channel, every 10 meters should be a reliable grounding once the meaning of the bridge along the laying of long ground flat steel, every 10 meters and the ground wire once. System cable design specifications: Section 3.7.1 The bridge system shall have a reliable electrical connection and ground. Section 3.7.2 When the use of the bridge system to allow grounded trunk circuits should meet the following requirements: First, the tray, ladder The connection resistance between the ends should not be greater than 0.Ω. The grounding hole should be removed insulation coating. Second, in the expansion joints or soft joints need to use braided copper wire connection. Section 3.7.3 along the bridge full length of the other laying ground , The staircase shall be connected at least one point to the grounded trunk in each section (including non-linear segments). Section 3.7.4 For vibrating spaces, a spring washer shall be provided at the connection of the grounding part.
- Q: Do you want to make a cross-sectional area of the jumper? What is the minimum cross-sectional area of square mm?
- The second I would like to ask you this 1 to 8 of the splitter is which level
- Q: Construction bridge size and price (price / per person / day) more
- Embedded, buried the best use of KBG, ceiling overhead look at the use of PVC, of course, is still the preferred KBG tube good!
- Q: Seeking cable bridge grounding is a few categories, grounding resistance standard is how much?
- The patch panel is the most important component of the management subsystem and is a hub for cross-linking the two subsystems of vertical and horizontal cabling. The patch panel is usually mounted on a cabinet or wall. Through the installation of accessories, patch panels can meet the full range of UTP, STP, coaxial cable, fiber, audio and video needs. In the network engineering commonly used patch panels have twisted pair patch panels and fiber patch panels. The function of the twisted pair patch panel is to cross-connect the twisted pair in the management subsystem, which is used between the main wiring lines and the distribution lines. Twisted pair patch panel models are many, each manufacturer has its own product line, and corresponds to 3 categories, 5 categories, 5 categories, 6 and 7 types of cables have different specifications and models, in specific projects , Refer to the product manual, according to the actual situation of the configuration. Optical fiber patch panel is the role of the management subsystem in the cable to connect, usually between the main wiring and distribution lines.
- Q: Can the cable bridge be installed above the cable tray? Is there a requirement in the installation specification? anxious! The More
- I have a 220V small crane, mainly on the 5th floor, hanging goods, control the small hanging switch wire is too short, I lengthened 20 meters, the switch down to the downstairs, easy to operate, in order to facilitate the small hanging switch Of the loading and unloading, I was in the wire with a car terminal connection, with the time to plug, when not on the pull, (commonly known as: public terminal, female terminal) when the copper terminal in the car is stamping in the 2 square wire The The problem came, since I connected the terminal, no use of a small crane, and later borrowed friends, borrowed, friends reflect the small hanging no effort to send to repair, repair the motor that high-pressure package where the line is not good, and finally The movement of the entire coil are changed, repair or no strength, is not my small crane switch extension cord with the reasons for the car terminal, the current is not enough, or other problems
- Q: Will the electric wire be able to travel with the ordinary wire?
- Puncture clips and T terminals need to remove the cable jacket, but the puncture clip does not peel off the cable core insulation layer, T terminal need to remove the cable core insulation layer. Puncture clip contact surface is small, firm degree of poor, simple and quick construction. T terminal contact surface is large, the installation is firm and reliable, but the construction is relatively difficult.
- Q: What about it? Is such a good classmate, his father is the chairman of the construction company (surname), the total pro-brother's brother is the cable bridge and distribution cabinet, I said to the students, he said no Good to do, so close relatives. I would like to ask your colleagues how do you say, the total of these projects involving dozens of homes it? Help ~! The More
- Power cable where it does not matter, as long as there is a certain safe distance can be.
- Q: Hello to ask a question, high pressure (10KV) bridge and weak bridge can be installed with a horizontal horizontal installation
- Textbook on the standard answer tube threading length = (piping length + reserved length) X wire root number of the formula is not the same length of the reservation, such as the line is 1.5m, from the ground pipe exports caused by power connection box is 1.0 ... ... generally consider the line length is 1.5 times the length of the tube just fine, the size of the difference according to the actual workload to change like.
1. Manufacturer Overview
Location | Tianjin,China |
Year Established | 2006 |
Annual Output Value | |
Main Markets | North America South America Southeast Asia Africa Mid East Eastern Asia South Asia |
Company Certifications | ISO14001:2004 ;ISO9001:2008 ;The SGS Certifications Of Cable Tray System |
2. Manufacturer Certificates
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability
a) Trade Capacity | |
Nearest Port | Guangzhou,Shenzhen |
Export Percentage | 31% - 40% |
No.of Employees in Trade Department | 11-20 People |
Language Spoken: | English, Chinese, German, French |
b) Factory Information | |
Factory Size: | 50,000-100,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered Design Service Offered Buyer Label Offered |
Product Price Range | Average |
Send your message to us
Strut Channel
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 100 Meters m
- Supply Capability:
- 200000 Tons per Year m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords