RJ45 jack contact,phosphor bronze,nickel-plate with gold-plating
ABS ,UL94V-2 with high precision brass shielded cover
2. Insertion force:
900gfor eight contacts.
3. Retention strength:
7.7kgbetween jack and plug
4. Operation temperature:
- 40 to 80 degree celsuis
jack 750 cycles plug-jack mating and unmating test,insertion cycles at 20 cycles/minute maximum.
6.Contact resistance test:
per 100 cycles.
maximum 200 punching times.
1pc in a bag,1000pcs in a carton
11. Category 6 performance
in compliance with the ANSI/TIA/EIA 568 B.2-1 standard
- Q:Philips 43-inch PUF6701 / T3 how to install set-top boxes
- Dark line means: buried in the trough in the strong / weak wire, generally wrapped in the wire tube
- Q:Ask the Supreme, I am the installation of electricians, often need to nail electrical trunking, before hammering with hammer and then on the expansion bolts, and finally with a screwdriver tightened.
- 0.6 refers to the 0.6KV, 0.6 / 1KV refers to the breakdown voltage of the cross-linked cable, the need for details can be Google cable products.
- Q:Telecom side design and construction routing drawings have P35
- . desktop computer monitor power supply need to connect directly to the power outlet, do not need the computer host power connection jack. . if the monitor with a computer host external power interface, will cause power overload, such as power supply power is not rich, then connected to the display can cause overload to form a lack of power. . the monitor power supply directly with the power outlet is also very convenient, not more than the computer chassis power jack trouble.
- Q:Help! The The LCD monitor flashes, but the screen is still black
- There is a connector, it does not matter, as long as the line wrapped insulation can be assured with the use.
- Q:In the edius in the material video to the timeline do not want the video inside the voice how to do
- My Changhong and you said the same situation, go to the dealer! I can not do well.
- Q:Do you need to make a ground wire when installing KBG and JDG tubes?
- Not according to the length of the expansion and contraction section, but according to the actual situation, the equipment installed place. , The actual installation, far more than the standard data of 30 meters, some one or two hundred meters did not increase, because the bridge is only 2 meters per meter or 2.5 meters, the middle of the connection, in the process design to consider the thermal expansion and contraction Of the problem, the connection with the film after the two sections of the bridge between the gap, the gap enough to meet the expansion of two meters of material. So many places did not increase. Norms are written right, in theory, all right, is not combined with reality. In theory, the bridge bolts fastened after connecting him as a rigid connection, as a whole, then tens of meters long things, of course, we must consider the expansion of the problem.
- Q:Layout of the integrated wiring data points and voice points 42u cabinet can be a number of data points and voice points? 9u?
- Is there a problem with your trip parameter setting? Also see if your coordinate system is set with your x move value vector and over the trip
- Q:Construction engineering underground pipe should be how to block so that it does not leak to the floor?
- Motherboard performance is not good, out of the problem, do not want to change the motherboard, then it will be used with it
- Q:Voice and data are used six types of cable, how to wiring in the patch panel
- SC in the hydropower drawings generally represent the electrical threading pipe material for the galvanized steel pipe, the diameter of the value behind the SC, and DN that is the nominal diameter of the pipeline. As shown in the figure SC. then the pipe threading pipe material for the galvanized steel pipe, the diameter of DN32.
- Q:How to solve the car when the GPS navigator restart the problem
- If the jacket line, line card spacing of 300 ~ 500mm, if the cable, according to the size of the diameter, the maximum can not exceed 2500mm. Add a fixed line card at a distance of 200 mm at the turn and at the wire box.
Our company has 700 staff members and strong technical strength. With advanced manufacturing equipment and precision testing instruments, we ensure that we can deliver the good in a short period of time. We can provide products according to your needs. We provide better solutions and strong technical support.
1. Manufacturer Overview
|Annual Output Value
||US$2.5 Million - US$5 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||31% - 40%
|No.of Employees in Trade Department
||English, Chinese, Japanese
||10,000-30,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range