quick form shaft formwork system made in china

Ref Price:
Loading Port:
Qingdao
Payment Terms:
TT OR LC
Min Order Qty:
3000 m²
Supply Capability:
60000 m²/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

quick form shaft formwork system  made in china 


Based on my pp plastic plywood, we develope a formwork unit for shaft /elavator system/.

  this system adopt advanced technology from EU.

size: can be made according to your drawing.

usge: formwork concrete shuttering of elevator shaft.

Rent: available.

brand: Square Circle Formwork

material: plywood + metal.

place of origin: China

factory located in Linyi, shandong,China

tech-support available.


work style:self-adjust and climbing .

        

   The inside form can re-size to fix and dismantle.

quick form shaft formwork system  made in china 


 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:I would like to ask the template support system Liang Xiaoliang Ban Xiaoliang refers to what
Directly subjected to loading template called small beam beam beam emerged called bear small load. The landlord asked the name of small square steel beam, 80 by 80 Fang Mu called Liang Xialiang; 70 by 70 Fang Mu challenge of small beam pipe is under the plate beam. In fact, there is no strict definition.By the way, there is no 48 by the steel pipe of this specification, recommended (suitable for use) is 48.3 x 3.6 Q235 material straight welded steel pipe, the market does not sell.
Q:Rules for calculation of formwork with beam slab
The board side mode *2 is the circumference of the board (minus column protruding part) multiplied by the thickness of the plate 0.1m.
Q:How to control the elevation of the beam bottom and the axis position
The axis is controlled by hanging the ball down to the lower floor axis and the axis control line.
Q:What are the middle and side beams in the T beam template?
Sandwiched in the middle for the [beam] and close to the abutment of a span [edge] the rest of the [medium]
Q:How to calculate the beam section size is 200 x 400
The side plate of the plate is the circumference of the plate (minus the protruding part of the column) multiplied by the thickness of the plate 0.1m.Beam slab:Plate beam T beam box girder is divided into cast in place PC box girder and steel box girderBeam type structural member composed of steel plates. The basic section is I-shaped, upper and lower transverse wing plate is vertical plate, the middle name web. Some plates are welded with reinforcing ribs. According to the combination method, it can be divided into welding plate beam, high strength bolt plate beam and dissimilar steel plate beam. Reinforced concrete slab beam.
Q:More than the number of square cross-section of the beam high formwork
For the height of more than 8m, the total load is greater than 15kN/m2, or the central line load greater than 20kN/m of the template support system needs to organize expert demonstration".
Q:The main floor beam template installation should pay attention to what?
2) install the side formwork of the beam and drill the side of the side of the side of the pull screw hole after the additional diagonal reinforcement.3 check the beam center line, elevation, section size, adjacent beam column template connection is fixed.4) after the beam and plate steel reinforcement is finished, the 1/2 pairs of the beam height are put on the pull screw, and the outer part of the pull screw is coated with a hard PVC casing, and the screw spacing is 1000mm.
Q:What is the meaning of the steel beam overhead on the top of the beam formwork
So in the form of the frame up binding, binding with a crane to lift the steel beam, the following overhead with the wood out of the beam of steel on the template
Q:Calculate the beam template when you want to reduce the thickness of the plate
Building template is a temporary support structure is made according to the design requirements, the concrete structure components, according to the position and size of the provisions of forming, maintaining its correct position, external loads and under construction template gravity and acting on the. The purpose of template engineering is to ensure the quality of concrete engineering and construction safety, speed up the construction progress and reduce the cost of the project.
Q:How to determine the height of cast in place concrete beam formwork
Span multiplied by 1/1000~3/1000, can not be so precise, the general is probably about two or three cm

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range