Q:What is the difference between solid wood composite board and plywood?

Process difference: multi-layer solid wood flooring and each slice will adopt scientific elimination of internal stress, arranged in a crisscross pattern, at present, the layers from the 7 layer to the 9 layer, 11 layer range; and general splint or plywood layers according to needs, relatively less in the balance of internal stress on the demand is far better than multi-layer solid wood this is our floor strictly, the daily common splint or plywood bend reason.

Q:Can the bamboo plywood used for building be made at home?

Bamboo plywood is made of bamboo material as the main structure and filling material!

Q:What is an offset press? And what are the machines for printing paper?

Offset lithography is a very simple, means of speaking that is offset rubber (Pib) will plate transfer to the substrate of printing, it is also the existence of Pib, named after the printing mode. The blanket has played an irreplaceable role in the printing process, such as: it can make up for a good substrate surface is not flat, so that the full transfer of ink, it can reduce the plate of water (see water in the role in printing) to the substrate transfer etc.. The above is only a general concept, we usually say that now the offset may be more narrow in scope, namely the three roller (printing, lithographic printing, embossing blanket), in the south of our country to the printing mode called offset printing.

Q:Do you make furniture, carpentry or plywood? Which one is more expensive?

The plywood formaldehyde wood board is more than 2, but has the best technology on the plywood formaldehyde, make the effect, especially the edge look good, and not to brush paint, short time limit, you do when manufacturers custom-made hydropower, hydropower well directly on-site installation of furniture, save a long time this woodworking process. If high, better paint what.

Q:Plywood (multi layer), this side of the small hole is what happened, please answer in detail!

This is the result of the production process,Multilayer plywood material is sheet logs spokeshave out, when the wood adhesive material grain interfolded, can enhance the hardness, both sides of the sheet is generally a little better, the middle part with broken material together, so there will be in the middle of the splicing gap, cut occurs when the holes.

Q:Plywood, furniture parts

Plywood is of high strength and good bending resistance. In some of the structural areas that require load-bearing, the use of a thinner core will be more intense. However, the stability is poor due to the consistency of the core material. This allows the deformation of the core plate to increase. Therefore, the core board is not suitable for single sided parts, such as cabinets and so on.

Q:9 mm splint what specifications, length and width of each is how much?

9 mm splint refers to the width of 1220mm*2440mm, thickness of 9 cm splint.

Q:Why are plywood cheaper than solid wood?

Without changing the physical properties of wood after drying, after liposuction, a process that can be called wood paint. Plywood (Plywood: commonly known as: multilayer board) is one of the common furniture materials, is a man-made board. The plywood is logs into veneer or by wood sliced veneer, with adhesive glued into three or more layers of sheet material, usually with odd veneer, and the fiber direction of adjacent plates perpendicular to each other and gluing. Is the destruction of the physical properties of wood itself, which plays a leading role in the composition of glue, so it will not crack, but it can not be called wood, there are now a wood particle board, MDF, particleboard and other sheet rubber ingredients except outside is sawdust, sawdust, straw and other wood fiber containing something very cheap, so the production cost is very low in density so the market price is cheaper than wood.

Q:Desulfurization absorption tower anticorrosive lining glue, specifications have stipulated, rubber board need sampling?

There shall be no leakage glue brushing brush, and each layer of mortar and its adjacent layers in the brush should be arranged in a crisscross pattern, and manufacturers should consider each layer of glue between color should have greater contrast, so it is easy to check out the leak brush. The year of the mucilage must be moderate, the viscosity of the mucilage is too large, and the appearance of the drying of the film is easy to appear. The surface of the adhesive film has dried and the inner solvent has not been volatilized, and the rubber plate will blister when it is vulcanized. In brushing the next mortar, we must ensure that the last glue has basically dried. In addition, the need to pay attention to the coefficient of thermal conductivity of rubber plate and steel shell is not the same, but the need to ensure that both the dry mortar and reach the rubber lining, so the glue coating time sheet in advance, and the steel shell glue coating should be slightly lag.

Q:What is copper paper or rubber paper?

Coated paper is an advanced printing paper made of base paper coated with white paint. Mainly used for printing books cover and illustrations, senior color pictures, a variety of exquisite product advertising, packaging, trademarks, sample. Coated paper is also called coated printing paper. It is called "powder paper" in areas such as Hongkong. It is an advanced printing paper made of base paper coated with white paint. Mainly used for printing books cover and illustrations, senior color pictures, a variety of exquisite product advertising, packaging, trademarks, sample.