Q:The hydraulic platform can't rise. Why?

The hydraulic platform and the control line are relatively simple, the hydraulic pump running at the point of rise will drive the oil hydraulic drive plunger up. Turn on the solenoid valve when the point is lowered. Be described in the hydraulic pump caused by dirt Chen Ji which reduces the pump fluid efficiency, hydraulic pump will be removed to clean the pump tablet, does not rule out the filtrate may be network jam.

Q:How to use the ball screw platform?

Second, heyman screw can see lu, platform settled on first use, carefully to see if there are any more abnormal hydraulic parts, electrical appliances, layout, to ensure that no more than about geomagnetic held before commissioning, no-load again after 3 ~ 5 times a load test.

Q:There are several reasons for the hydraulic cylinder oil leak on the elevator

The sealing part of the seal is worn out to buy two oil seals according to oil cylinder model to change to be good also a few dollars

Q:What is the elevating platform for automatic mahjong machine?

The bearings and screws on the lifting mechanism fell off. Solution: open the lid of the machine box under the mahjong machine, and you can see a circular black iron piece fixed on the motor, with a screw hole in it. Find screws and bearings in the box, spring pads, some machines and nuts. Just fix it up.

Q:Where do the elevator motors go?

Abstract: the shear fork type electric elevator is a special equipment for high altitude operation. The it scissor mechanical structure, make the lifting platform lifting Has high stability, wide operating platform and high bearing capacity, make the work high above the range is bigger, and is suitable for many people work at the same time. It makes high-altitude work more efficient and safer. It is a special equipment for high-altitude operation. Characteristics: the lifting mechanism adopts high strength manganese steel. There is a safety protection device that prevents the elevator from overloading. Safety valve shall be set up to prevent rupture of hydraulic pipe. An emergency reduction device with a power failure. The product is suitable for high-altitude equipment installation, maintenance, etc. According to different requirements can choose different dynamic form (such as: three-phase ac power supply, single-phase ac power supply, dc power and diesel power, etc.), and with manual hydraulic equipment, can be in a power outage or lifting work as usual, no power supply and can add adjustable platform, can extend to the desired location on the length of the platform, so as to improve the work efficiency. It is the ideal of modern high building and equipment, which is necessary for the production of high-altitude safe civilization.

Q:What is the main shaft of the horizontal milling machine

CNC horizontal knee-type milling machine is rigid and can withstand heavy load cutting. The CNC horizontal knee-type milling machine has sufficient power and wide spindle speed range. Can use carbide tool for high-speed cutting and make full use of tool efficiency.

Q:How to choose the platform and how to use the method

With the development of science and technology now society, lifting platform has spread to every corner of the social life, more and more widely use, whether it is architecture, civil engineering, and People's Daily life is inseparable from the lift machine, many businesses to grasp the business opportunities, invest in succession, lifting machinery company with full in each big industrial cities like bamboo shoots after raining, lifting platform market is hot, in short supply, it can be seen from the side, now, and the rapid development of society, promote the development of the industry and the demand of people, however, as the buyer how to choose good lift machine in a forest of products become the important topic today

Q:How to use the elevator to be safer and more efficient

Annual maintenance Check all hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. Remove the hydraulic oil, remove the oil strainer and remove the oil strainer, clean it up and then put it back in the tank. Be familiar with 'ten notices' 1, pay attention to the agencies should regularly check and adjust the brake of the brake and the clearance between the brake wheel, flexible and reliable. The clean surface, there should be no dirt, in case of dirt must wash with gasoline or thinners. 2, pay attention to removing the hydraulic tank of fuel cap, remove the cap around earth, unscrew the cap, remove residual impurities in the joint area (not rinse in order to avoid water seeping into the tank), confirmed to open the cap. 3, pay attention to the elevator remove the hydraulic tank of fuel cap, filter cover, test hole, hydraulic tubing parts, cause the system oil when exposed to avoid dust, remove the parts to open completely clear before first.

Q:Safety operation of hydraulic platform

The driver shall be responsible for monitoring the distribution of the goods on the platform as uniformly as possible to prevent partial load and to prevent overload operation. The platform does not allow people to carry dangerous goods, such as inflammable and explosive devices, and to ban people from climbing as they rise, as well as artificial shaking. Drivers in the platform are strictly forbidden to leave their posts and to wipe, lubricate or repair the platform. When the work is finished, the driver should cut off the power supply and lock the control panel to leave the job and fill in the record of the transfer. 31 malfunctions, platform, or lose the normal work, should immediately notify the maintenance personnel to repair, if found to have dangerous or may cause personal mechanical accident, should immediately stop using, the total power cut off room and report to management department, just can use after repair and check in detail.

Q:Does the fixed hydraulic platform need to submit to the specification requirement

There is no clear regulation of hydraulic lift and hydraulic platform in China, which means that you can also do it without testing. Local regulations may be different. Also, if you check, you are going to the local quality and technical supervision bureau. Should go to the special branch to register, apply for installation, after installation is finished again ask them to check the acceptance of the check. There is a fee for it. And it will be checked every year.