Hydraulic hose fittings for 2SN DN6

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PART NO.HOSE BOREDIMENSIONS
DNDASHL
00400-046437.5
00400-0610639
00400-0812841
00400-10161043
00400-12201251
00400-16251661.5
00400-20322067.5
00400-24402475
00400-32503279

Material: Carbon steel, alloy steel, stainless steel, aluminum alloy and brass.

JIC, SAE, DIN, BSP, JIS and ISO standards

Products:high pressure hose, pipe and tube fittings, flange adapters, straight fittings, tee fittings, cross fittings and various adapters

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Why should the high pressure hydraulic tube peel off the outer skin?
Skinning requirement:The stripping length of hydraulic hose shall be two to four mm shorter than the caseA layer without peeling, more than two layers stripped to see the steel wire, otherwise the shell is easy to fall offThe size of the joints to be installed depends on the size of the joint and the quality of the hose, just start recording more to find the most suitable size.
Q:Can the rubber hose for the LPG cooker and gas cooker be general?
However, attention should be paid to the isolation of fire sources during storage and transportation, avoiding the exposure of sharp instruments and more corrosive chemicals, and avoiding prolonged storage in daylight.
Q:Do the rubber joint and Y filter need flange connection?
To look at the general caliber, less than DN50 also has threaded connection type (i.e., thread), but flange type is more reliable.
Q:What is the difference between the precast beam of the bridge and the method of pulling out the rubber tube after pouring the concrete? What's the difference between design and calculation?
Construction process, in order to avoid concrete into bellows, influence later wear steel strand, construction units generally use PVC and other rubber tube into bellows, in order to double insurance, don't let concrete into. Its length is certainly larger than the length of bellows (750mm at one end for easy operation)
Q:How can I remove all the flavor on the rubber hose?
After the hot water is directly boiled, wrap it directly with transparent glue
Q:Toilet hose and water tank joints leaking, how to repair?
No rib sleeve, the use of pipe outside the buckle fixed, sealed, may be the aging of the tube, buckle clamping difficulties and other reasons. If the pipe is aging, you can cut or replace the tube in the aging part. It is difficult to buckle and clamp, so you need to change the buckle.
Q:What are the methods of sterilizing rubber hoses and Perspex?
Plexiglass products, we are placed on super clean bench, UV irradiation above 30min. Sometimes it takes time to wipe with 60% alcohol cotton ball.
Q:What glue can glue rubber tube?
1: clean: high temperature, quick drying glue, use dry cotton cloth or sand paper, then dust, oil, rust, etc., and then use the treatment agent or cleaning agent to clean, then clean the surface.2, sizing: flexibility speedglue unscrew the front cover, can be used as a glue bottle with cotton cloth to wipe clean and quick drying glue, can be set using needles or PE dropper, to control the flow of glue, ensure the bonding effect.
Q:What's the smell of petrol in the car and the trunk?! Especially after a long drive!
Have changed the gasoline pump, or because of the failure to disassemble the steam pump owners, if the car appeared gasoline, do not panic, this is because after the disassembly and assembly, the residue is not cleaned up. In fact, this situation is usually not met, the gasoline pump replacement cycle is 100 thousand kilometers. But now the gasoline filter is also installed in the tank, connected with the gasoline pump, and its replacement cycle is shorter, 40 thousand km, when the replacement of gasoline pump disassembly. In this case, just look at the gasoline pump installed is not correct, in cleaning the perimeter can be.
Q:How can the rubber tube be used properly and how to use it properly?
The hose burst caused by frequent and severe pressure impact. This situation is not generally under the static pressure caused by too much, but the number and intensity and pressure impact. Engineering machinery in operation, will be repeated in the hydraulic tubing suddenly increased or decreased, which impact on the oil pressure of frequent the damage of the oil seal, resulting in increased, loosening hose leakage and rupture foaming and pipe joint. Therefore, in operation, the valve stem can not be too hard, must be gentle.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range