Ex-proof aerial working platform

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Q: Does the fixed hydraulic platform need to submit to the specification requirement: There is no clear regulation of hydraulic lift and hydraulic platform in China, which means that you can also do it without testing. Local regulations may be different. Also, if you check, you are going to the local quality and technical supervision bureau. Should go to the special branch to register, apply for installation, after installation is finished again ask them to check the acceptance of the check. There is a fee for it. And it will be checked every year.

Q: What is the elevating platform for automatic mahjong machine?: Mahjong machine able to shuffle out of the card, is the panel can't lift, center lifting motor and induction electric is good, the fault in the center of lift pipe should be fixed on the arm

Q: The hydraulic platform is compared with the normal lift platform: Compact structure, small size of transportation, can enter the car of general elevator and pass through door and narrow passageway smoothly.

Q: What is the phenomenon of the worker's transport of wood using a lift: Imobile elevator accessory device can be configured for any combination, such as lifting capsules can be used with the inward and outward transportation equipment, make fully automated conveying process, operators need not enter the elevator, so as to ensure the personal safety of operators, and can realize the goods transport between floor, to improve the production efficiency; Electrical control mode; Work platform form; Dynamic form, etc. Limit the function of the elevator to achieve the best use effect. Imobile elevator optional configuration of hydraulic power, convenience and the surrounding the lap joint of frame, roller rolling or motor, prevent pinches safe touch, organ type safety guards, moving or motor rotary worktable, hydraulic flip table, to prevent falling elevator safety support bar, stainless steel security guard network, power system of electric or hydraulic elevator walking, mesa of ball. A stationary lift is heavy in weight. It's not affected by the environment.

Q: What can be done when the hydraulic platform is down?: The left and right sides are connected by wire rope, while the other side is synchronized.

Q: The structure of the universal elevator milling machine: The main shaft is used to install the tool pole and rotate the milling cutter. The main shaft is a hollow shaft with a 7:24 precision taper hole in the front, which is used to install the taper shank of the milling cutter. The longitudinal platform is carried by longitudinal screw, which is carried on the guide track of the turntable, and the workpiece on the surface of the table is moved vertically. The T groove on the surface of the table is used to install the fixture or workpiece.

Q: Can the stepping motor drive the hydraulic platform?: Are you a driver for this motor? But the normal step motor is only for torque, step Angle, phase number, not for rotational speed; It may be a servo motor or torque motor, and if the speed is low it is the possibility of torque motors. In addition, you can measure the current, voltage or waveform below.

Q: Operation and attention of electric elevating platform car?: When the working pressure of the platform is too high or the noise is abnormal, the inspection should be stopped immediately so as not to seriously damage the platform. For general failures, see (troubleshooting and troubleshooting); G, the wind should not be greater than 5 when used, and the machine should not be used in thunderstorm. Note: A, non-electric professional personnel should not disassemble the electrical appliances at will, in case of electric shock or mistake. B: the platform should be hoisted on the platform when the platform is being repaired under the platform. In case the platform suddenly drops, causing casualties;

Q: The automatic mahjong machine has a lift station always one. What is the other three normal: Up when you use hand pressure, will watch it sink after coming up, if I don't stop for a second long came up again can eliminate motor, friction, but institutions, hall signal detection, duplication of effort.

Q: What is the main shaft of the horizontal milling machine: Horizontal movements of spindle of the milling machine is driven by servo motor, each after a pair of tooth belt pulley deceleration, to the longitudinal, transverse and vertical feed movement of the ball screw to achieve three direction.

Send your message to us

*Email

*TEL

*Quantity

*Unit