Ductile Iron Wafer Butterfly Valve

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT OR LC

Min Order Qty:: -

Supply Capability:: -

Inquire Now

Chat Online

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Specifications

Good quality and performance,cost-effective,ligher and smaller in comparison to a conventional swing check valve or lift check

Technical Data

DN40-DN600mm PN1.0-1.6MPa

Body: Cast Iron, Ductile Iron, Carbon Steel, Stainless Steel

Seat: EPDM, NBR,Stainless Steel

Stem: Stainless Steel

Disc: Ductile Iron with Nickel Coating,Ductile Iron with Nylon Coating, Stainless Stee 304/316l, Alu-Bronze

Spring:Stainless Steel

Flange Connection:DIN,ANSI,BS,JIS,UNIVERSAL FLANGE

Product Features

Wafer body style fit between FF or RF flanges

Upper and lower PTFE thrust washers

Resilient Buna-N or EPDM Seat

Dual plate valves give maximum strength with minimum opening time

Torsion springs assist valve closure, preventing flow reversal

Thrust washer reduce friction and wear of valve plate hinges.

Q:Other water pipes are through, only the kitchen faucet no water, what reason: First, the water supply pressure is low, and your kitchen faucet position is high just out of water, can be installed pressurized pump or contact the property to solve. Second, it may be blocked. Leading the outlet, there is a filter, the most likely to block, you can screw down to see three, the kitchen water valve damage, open repair or replacement. Fourth, the management of fouling, cleaning and maintenance. I hope that my reply is helpful.

Q:I would like to give a sink and faucet the appearance of having plumbing for display purposes. Is it possible to use a fountain mechanism to create that effect. I'd like to be able to turn a handle and have the water flow, then drain back down into a basin to be pumped through continuously if left on. but able to be shut off by simply turning the handle back to the off position.: yes, the faucet would either have to be a switch to turn the pump on and off or a valve by which the constantly pumping water is diverted from a self contained tank to run through the sink

Q:Kitchen faucet leaking the total valve is also not how to do: change

Q:It's very important that I do this the right way. (I sort of told the people I was working with that I knew how....but I don't) I bought a new faucet from Lowe's, and it has instructions on the back but I think I'm missing something. They also said something about the plumbing being bad and hard to work with? I've never done any kind of plumbing in my life.: In laymans terms, you are screwed! Naw, just kidding! under the sink and on the back side there are two lines attached to the faucet. Use a crescent wrench to loosen the connectors (turning them to the left as you are looking at the back of the sink. (make sure the supply water is off). After removing them, there will be a nut on each side of the faucet loosen and remove them. Set the new faucet in place and reverse the actions. Now you are a plumber!

Q:I've read step by step tutorials I found on google, but I'm stuck at only the first few steps! After turning the water off I was going to disconnect the supply lines as well as the nut that holds the current faucet onto the sink, but it seems as if it's in the counter. I don't know if that's clear enough, but the lines run into the counter it looks like, I was wondering if there was anyway I can reach this without going to extraordinary lengths like taking the countger top off: I think that U are describing that U cannot reach or even see the nut. there is a special wrench made called a plumbers wrench. It is a steel post about ten inches long. The top of the post has a set of horizontal jaws like those on a pipe wrench. The bottom of the post has a long rod that provides leverage so that U can turn the wrench from below. To turn the wrench in the other direction the jaws can be flipped over. Now U know why plumbers earn the big bucks ~~~~~~~ I try to not turn the water valves off in the bathroom. The valve often starts to leak and can be very difficult to change. Turning off the water from outside of the house leads to many other compllications though.

Q:how can i change the kitchen faucet and sprayer?: 'Wired has it right, but forgot: Measure the 'hole pattern' in your existing sink/countertop and be sure that the replacement you buy has the same pattern. There are different numbers and spacings of those holes. It's maybe a two hour job for an experienced plumber. You should be able to do it in less than a day.

Q:Kohler faucet on the top of the bubble where to sell: Go to the Kohler store to buy

Q:He won't drink from a bowl of still water or a small fountain with running water, even when the water is fresh. He only drinks water from a running faucet, or from knocking over a cup of water and drinking it from the ground. My concern is whether he is getting enough water, because I only turn on the faucet a couple of times each day for him.: You don't mention what your cat eats. If your cat eats dry food then you really do have a problem but if he eats an all wet diet the water he is getting should be sufficient. In nature our cats' ancestors got all their water from their prey, which is about 70% water. So cats don't have much of a thirst drive since they are made to get their water from their food. When the cat eats dry food this becomes an issue because cats do not have sufficient thirst drive to make up the difference. Even though they may drink more on dry food they do not drink enough to make up the difference. If he eats dry food one solution then would be to switch him to a 100% wet diet. Another solution would work if he will drink water from the bathtub tap. You could let it trickle with a basin under it. That way you wouldn't waste the water - you could still use it to wash dishes, water plants, or to flush the toilet. You could also rig your own fountain type of thing. You would need to buy a submersible pump made for small garden pools. They come with tubing or you can get tubing from wherever you get the pump. You get a clamp for the tubing to regulate the flow. The type you'd need would be fairly cheap because you'd be looking for one with a very low maximum flow rate that is one for very small pools.

Q:How did your faucet get the water fast? Can you tell me?: Faucet water flow is usually the mouth of the mouth of the arc 碃碃瞢瞢瞢瞢瞢瞢瞢护护护护护子子子局慢慢慢慢慢慢慢慢慢慢慢慢慢慢慢慢慢慢慢慢

Q:Basin basin faucet and sink faucet with what brand is better?: My home is made of stainless steel sink and faucet, Oh, with five or six years, and feel very good. Mainly easy to clean, the quality did not have problems.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range